|\     /|
| )   ( |
| | _ | |
| |( )| |
| || || |
| () () |
(_______)
         

         
         
  ####   
     ##  
  #####  
 ##  ##  
  #####  
         

         
 ##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 #####   
         

_________
\__    _/
   )  (  
   |  |  
   |  |  
   |  |  
|\_)  )  
(____/   
         

      _ 
     | |
  _  | |
 | |_| |
  \___/ 
        

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Ruben's Mazda rotary '''RX-8 engine in MX-5 track only car''': Engine 13B 2 rotor, 2 Rotor, 2 plugs per rotor, leading/trailing arrangement 6 high Z injectors, 3 per rotor, 2 banks 1 bank 2 primary injectors, 1 bank with 4 secondary injectors staged on rpm/load 4 active coils (LS2 truck coils, 5v TTL singal required) wheel speed not required minimum 3 PFET outputs required: 3 solenoids to control intake manifold/ports based on rpm relay output for cooling fan and fuel pump would also be nice Single Wideband required, '''preferred LSU4.9''' Dual EGT inputs required (1 per rotor) Fueling algorithm: preferred alpha-N with realtime barometric pressure correction based on airbox pressure (to eliminate influence on fueling in case of clogged airfilter, ram air, etc) ---- How much '''analog inputs''' are left over? * You can request "2 EGT + min 4 analog inputs" in the order comment. ** If no pins left on EC18, than flying loom SSC6 or EC10 will be used. The rest seems nothing special. ---- Triggerwheel: stock RX-8 wheel, often called 36-2-2-2, picture of wheel: http://www.rx8club.com/attachments/series-i-aftermarket-performance-modifications-23/55065-viability-megasquirt-application-fi-renesis-rx-8-trigger-wheel.jpg Can you tell me which VEMS ECU / Round options I need? Most rotaries installed before were HALL / HALL type, * but '''yours seem VR''' (subaru style, with correct polarity), ** '''please confirm (measure resistance in both directions, write here VR=... Ohm''') ** please, (perhaps after ordering, but before the benchtest of the config), please provide approximate ignition points information (leading and trailing spark). Numerically, or marked on the wheel image. ---- I read nothing but good about the VEMS ecu and now my 2 specifik questions are: >-will it work with the 36-2-2-2 wheel? yes, supported without sectrig, or with sectrig. > -Will trailing ignition work, if yes, does it have a rpm/load map just like normal ign timing to specify either absolute angle or better, split angle. Most often 24 tooth wheel is used for rotary + trailing spark. But 36-2-2-2 should also work. (with the 128 (0x80) in reftooth method, we'll recommend and benchtest config when you publish output wiring plans). ---- '''Data output to race technology Dash2''' required (serial) AIM stream is sent via serial port (if enabled). "race technology Dash" previously sold interface for "VEMS" that simply did not work (Race-tech did not test it), at least not without fw update available later after users nudging. Later they provided fw update on request. Version of "race technology Dash" should be preferred that uses interface/fw AIM serial stream on the input (possibly the Motec fw version ?). ---- I would like to buy a VEMS ECU. Actually the car has ran fine for 3 years with a kdfi v1.3, which died for no reason (crappy multilayer PCB), I ordered a new kdfi v1.4 but this unit is even faultier when new and there is no support at all. therefore I am sick an tired of k-data and kdfi and I want now a decent ecu where there is support in case needed.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.