|\ /| | ) ( | | | _ | | | |( )| | | || || | | () () | (_______)
_____ |_ _| | | | | _| |_ \___/
## ### ## ## ## ######
____ | _ \ | |_) | | __/ |_|
__ __ \ \ / / \ V / \ / | | \_/
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: I would like to install a Genboard v3.3 to the following car: Audi S2 coupe quattro 2.2 5 cyl 20v 3B This 5cyl needs InputTrigger/AudiTrigger see config info * see GenBoard/UnderDevelopment/FirmwareChanges * MegaTune r027 or later will be needed (r028 should work too). **'''When I can use the new modified software version of original auditrigger?''' While the trigger is special, the other sensors should be no problem at all. My V3.3 include: * Primary trigger VR * secondary_trigger: auditrigger * MAP connection: 400kPa onboard * LCD an PS2 * 2 Knock and EGT * ignition driver: 6+2 The car use the absolutely factory sensors and accessory but the air filter's house was removed. I want to make a street racing car from above. Project to follow: * samco turbo hoses * tubular turbo exhaust manifold * bigger turbo than original * erl water injection * engine internal modification /pistons,conrods/ My plans: * use a factory 55 pins Motronic male connector to EC18 and EC36 and make a flying cable set + WBO2,egt custom made wirings to engine. * Anti lag system * Launch control * Boost control solenoid * Distributor based ignition * Sequential injection for 5 cyl '14.5 ohm' * 2 knock sensors, but I think use 1 knock sensor. If I want to use the factory airmass sensor too,where can I connect this? Since you have onboard MAP, EC18pin6 (see WebShop item http://shop.x-dsl.hu/catalog/product_info.php?cPath=1&products_id=48) is a custom analog input that you might use for airmass sensor (not used by default, just logged in MegaTune). The knock input cannot measure the airmass sensor's signal. * Primary trigger VR 135 tooth crankwheel (no missing tooth) * Secondary tr. HALL trig 1 window/720° camtooth. Overlaps VR. * Secondary tr. VR trig 1/360° cranktooth * factory CLT * factory IAT * factory TPS * 1xWBO2 * 1xEGT * LCD Please check my planned pinout and correct it if necessary. '''EC36''' 1 TPS sign. 2-IAT 450-650 ohm/in 20°C 3- fast-idle small solenoid or relay (or any low-current output, such as shiftlight). EC36pin3 is a 350mA output, see GenBoard/Manual/DigitalOut/Table. You might want to use the powerful injector outputs first (don't forget to adjust h[0]=.. entries) and use the low-current outputs if you run out of injector outputs. Care is needed to not overload outputs. 4- 5-'''GND5''' 6- 7-Injector1 14.5 ohm/in 20°C 8-Injector3 9-Injector5 10- 11- 12- 13-Sec.trig HALL 1 window camtooth 14-CLT 2.1-2.9kohm/in 20°C 15-Fuel pump relay 16- 17- 18-BOOST solenoid 19-Injector2 20-Injector4 21-'''GND5''' 22-'''GND5''' 23-'''Inj.flyback''' injector common (+12V) 24- 25-Vbatt 15+ 26-GND ecu and sign,knock 27-Primary trigger 135 cranktooth VR 28-5V to sensors /to TPS maybe ???? 29- 30- 31- 32-'''GND5''' 33- 34- 35-ignition coil 36- http://shop.x-dsl.hu/catalog/product_info.php?cPath=1&products_id=48 says channel3=EC36pin36 and channel5=EC36pin12 are logic-level drive. Useful for active coils that have the driver stage inside. For traditional dumb coil, you want to use one of the 6 power (non-logiclevel) ignition outputs. h[2]=.. (ignition sequence) must be adjusted for the chosen output in any case. '''EC18''' 1 2-Knock1 3- 4- 5- 6- 7-WBO2 pump- 8- 9-WBO2 pump+ 10- 11- 12-Sec trigger '''1 Cranktooth VR''' 13-WBO2 nernst cell 14-Comm RS232 See [http://shop.x-dsl.hu/catalog/product_info.php?cPath=1&products_id=48 assembled genboard item in shop] 15-Comm RS232 16- 1-wire is a network connection. Not used (unless for [http://shop.x-dsl.hu/catalog/index.php?cPath=1_10 i-button]). A free connection (if you don't solder the DS2480B chip) - use for whatever you like. 17- 18-WBO2 heater- '''DO NOT forget to read the warning of the provided resckue-kit paper''', about GND5, flyback, and fuses. ----- Please link to the docs you're trying to use. See MegaTune page for (simple unzip) install. The v3.3 has max232, so a standard RS232 port is needed. See GenBoard/Manual/CommHardware If unsure about MegaTune setup / compatibility, in 9600,8n1 say <code> Man mll mcd mct bye </code> without spaces. mll prints LCD content of active page (even if no LCD connected), mcd and mct prints config and tables. bye (note: everything is case sensitive) goes back to MegaTune compatible mode. Since MegaTune is much simpler to use, you don't need to learn GenBoard/MenuSystem, but if you like: But 1.0.19 will NOT work with the InputTrigger/AudiTrigger , since it is a new development. ------- megaloq viewer: http://www.vems.hu/wiki/index.php?page=LogAnalysis you can also collect some infos from: http://www.msefi.com/index.php Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.