_____
 |__  /
   / / 
  / /_ 
 /____|
       

 _   _ 
| | | |
| |_| |
|  _  |
| | | |
\_| |_/
       
       

         
    ###  
   ##    
  #####  
   ##    
   ##    
   ##    
         

 _   _ 
| | | |
| | | |
| | | |
| |_| |
 \___/ 
       
       

 _____ 
/  __ \
| /  \/
| |    
| \__/\
 \____/
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
I would like to install a Genboard v3.3 to the following car: Audi S2 coupe quattro 2.2 5 cyl 20v 3B My V3.3 include: - Primery trigger VR - secondary_trigger: auditrigger - MAP connection: 400kPa onboard - LCD an PS2 - 2 Knock and EGT - ignition driver: 6+2 The car absolutely factory but the air filter's house was removed. I want to make a street racing car from above. My planning: -I use a factory 55 pins Motronic male connector to EC18 and EC36 and make a flying cable set + WBO2,egt custom made wirings to engine. -Anti lag system -Launch control -Boost control solenoid -Distributor based ignition -Sequential injection for 5 cyl '14.5 ohm' -2 knock sensors, but I think use 1 knock sensor and the other knock's input I use the factory airmass sensor -Primery trigger 135 cranktooth VR -Secondary tr. hall trig1 camtooth -Secondary tr. VR trig1 cranktooth -Factory CLT,IAT,TPS -1xWBO2,EGT -LCD Please check my planning pinout and if this not right you send for me please the correct. EC36-1 TPS sign. 2-IAT 450-650 ohm/20cels 3-Idle actuator??? or boost control solenoid 4- 5-GND5 6- 7-Injector1 14.5 ohm 8-Injector3 9-Injector5 10- 11- 12- 13-Sec.trig HALL camtooth 14-CLT 2.1-2.9kohm/20Cels. 15-Fuel pump 16- 17- 18- 19-Injector2 20-Injector4 21-GND5 22-Injectr flyback+12v 23-Inj.fly.+12v 24- 25-Vbatt 15+ 26-GND ecu and sign,knock 27-Primary trigger 135 cranktooth VR 28-5V to sensors /to TPS maybe ???? 29- 30- 31- 32-GND5 33- 34- 35- 36-Coil /Distr.based ign/ or to the 35???? EC18-1 2-Knock1 3-Knock2 or air mass sensor??? 4- 5- 6- 7-WBO2 pump- 8- 9-WBO2 pump+ 10- 11- 12-Sec trigger Cranktooth VR????????????????????? 13-WBO2 nernst cell 14-Comm rs232 DSUB pin3 15-DSUB pin2 16-??????????? what is it? 17- 18-WBO2 heater-
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.