_______ 
(  ___  )
| (   ) |
| |   | |
| |   | |
| |   | |
| (___) |
(_______)
         

 _______ 
(       )
| () () |
| || || |
| |(_)| |
| |   | |
| )   ( |
|/     \|
         

         
         
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
         

         
 ##      
 ##      
 ## ##   
 ####    
 ## ##   
 ##  ##  
         

 _   _ 
| | | |
| | | |
| | | |
| |_| |
 \___/ 
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
* Can you put more details of your intended setup please (trigger type etc.) I'm sorry, i'm not familiar with wiki. Trigger: 60-2 Bosch Type on crank, Polarity of sensor checked with scope - looks good. Two Lamps for Ignition and Injection Output. GND and GND5 Connected to Ground. 12V Connected to Pin25. Checked everything from the beginners guide. LCD is working, RS232 is working, Keyboard is working, even EGT1 is working. Code is now 1.0.13, it is the code which comes with Megatune 2.25b531. I did NOT Compile the code, i flshed Genboard with vems.hex. My h[0] Table: 01 02 00 00 00 00 00 00 My h[2] Table: 01 03 01 03 01 03 01 03 mdh80 and mdh90 switches on Injector Lamps, mdh00 and mdh10 switches them off. mdh92 and mdhb2 switches on Igniton Lamps while mdh12 and mdh32 switches them off. Injectors are connected to INJA and INJB (Pin 7, 19), Ignition Outputs are IGN1 and IGN3 (Pin 33, 36). TPS, CLT and IAT is connected as Poti. MAP is onboard. First I tried to configure WBO (with another firmware - i think 1.0.14) but WBO pump pw zero was unable to configure, i had always the same PW, and the same Voltage output between Pin 5 and 6, slightly over zero. * I am definately no authority on VEMS so take this advice with caution, I just had the same problem. Do your change in MegaTune. click send to ecu them shut off the power and turn on again. Reissue mde02 on the keyboard, wait for megatune to display O2 readings and recheck, That worked for me. Then I tried to configure the Trigger and the Outputs. My config is below. I tried also to configure with megatune and with different values but I never got one Lamp to flash. I have a Workbench with a Triggerwheel and an Electric motor to simulate the engine. When I start the FuelPump Relay switches on, i see a RPM Output on the LCD (which is now O.K. - it was halve of the real RPM) but none of the Lamps even glimms. rpmk is 0bb8. * I found [http://vems.sourceforge.net/manualhtml2/ch07s07.html this] last night. If you read it again you will find what I think is the answer. If you scroll down through your config, I have given my guess. Remember, I have ZERO experience, use info with caution I really don't know why, maybe somebody can help me. 19.8.05 Thank you so much! secondary Trigger was the problem. It should be 02! This is a very important Information. Tomorrow i try to configure wbo. good night. <code> primep=8A primep_temp_scaling=8A cwl=88 cwh=8A cranking_thres=03 awev=26 awev_temp_scaling=90 awc=FF warmup_clt_range[0]=00 warmup_clt_range[1]=15 warmup_clt_range[2]=28 warmup_clt_range[3]=3C warmup_clt_range[4]=50 warmup_clt_range[5]=64 warmup_clt_range[6]=78 warmup_clt_range[7]=8C warmup_clt_range[8]=AA warmup_clt_range[9]=C8 warmup_clt[0]=C0 warmup_clt[1]=B4 warmup_clt[2]=AB warmup_clt[3]=A8 warmup_clt[4]=A0 warmup_clt[5]=9A warmup_clt[6]=8C warmup_clt[7]=7F warmup_clt[8]=73 warmup_clt[9]=65 warmup_rpm_scale=DD req_fuel=64 divider=02 alternate=01 injopen=20 battfac=10 kpafac=7D kpaoffs=80 injocfuel=08 injrampup_battfac=FF injpwm=38 injpwmt=08 injpwm6=20 rpmk[0]=0B rpmk[1]=B8 tpsdot_kpadot_conf=00 tpsdotrate[0]=05 tpsdotrate[1]=0E tpsdotrate[2]=20 tpsdotrate[3]=40 tpsaq[0]=08 tpsaq[1]=12 tpsaq[2]=17 tpsaq[3]=1B tps_thresh=05 tpsasync=02 acmult=64 tpsacold=05 tpsdq=64 decel_fuelcut_thres=FF overrun_fuelcut=10 overrun_fuelresume=0F rev_limit=40 airden_ignore=62 config11=31 config12=30 config13=02 batt_cal=BC fastidle=80 baro=64 dbaro=0C tps_low=20 tps_high=F0 fan_temp=55 fan_hyst=09 fan_channel=FF iac_step_seq=C9 iac_conf=7A iac_max_steps=FF iac_tps_thres=05 iac_cold_idle_temp=A0 iac_warm_idle_temp=D0 iac_cold_rpm=74 iac_warm_rpm=67 iac_cold_start_pos=E2 iac_warm_start_pos=B0 iac_afterstart_rpm=1F iac_afterstart_duration=20 iac_afterstart_steps=04 iac_kp=25 iac_ki=10 iac_kd=30 iac_integral_speed=C0 iac_integral_limit_dec=05 iac_integral_limit_inc=E0 iac_integral_deadband=0A iac_deadband=05 iac_pid_conf=01 iac_overclose_interval=B8 iac_ref_pos[0]=35 iac_ref_pos[1]=34 iac_ref_pos[2]=33 iac_ref_pos[3]=32 iac_ref_pos[4]=31 iac_ref_pos[5]=30 iac_ref_pos[6]=2F iac_ref_pos[7]=2E iac_ref_pos[8]=2D iac_ref_pos[9]=2C iac_sol_channel=77 iac_ign_advance_change=28 iac_ign_retard_change=20 iac_ign_advance_limit=10 iac_ign_retard_limit=18 iac_ign_threshold=08 ego_conf=07 ego_lag=04 ego_coolant=00 ego_maxtps=FF ego_maxmap=FF ego_minrpm=04 ego_maxrpm=FF ego_warmup=3C ego_lean_limit=1D ego_rich_limit=28 ego_pid_kp=40 mt_unused=00 ego_delta=01 ego_target=19 ego_pid_window=FF wbo2_warmup_ramp=A0 wbo2_warmup_target=FF wbo2_abs_limit=E4 wbo2_limit_maxt=A0 wbo2_fallback=60 wbo2_retry_t=06 wbo2_edgetime_corr=BA wbo2_edgetime_min=50 wbo2_ri_target=A1 wbo2_nernstdc_target=8F wbo2_pump_pw_zero=78 wbo2_calibration=AE wbo2_heater_pid_kp=20 wbo2_heater_pid_ki=10 wbo2_heater_pid_kd=1A wbo2_heater_pid_ilimit=A0 wbo2_pump_pid_kp=42 wbo2_pump_pid_ki=01 wbo2_pump_pid_kd=00 wbo2_pump_pid_ilimit=E0 wbo2_ri_confidence_scale=80 knock_conf=01 knock_sampling_window=F2 knock1_frequency=29 knock1_gain=40 knock1_integrator=14 knock2_frequency=29 knock2_gain=40 knock2_integrator=14 knock_threshold=FF knock_noise_scale=D8 knock_max_retard=28 knock_default_retard=04 knock_retard_step=08 knock_retard_delay=FF knock_advance_step=FF knock_advance_delay=50 knock_minrpm=FF knock_maxrpm=05 ve_learn_coolant=D8 ve_learn_max_power=FF ve_learn_rpm_scale=1E ve_learn_kpa_scale=1E ve_learn_ego_scale=43 ve_learn_min_weight=4D ve_learn_speed=FF ve_learn_limit=FF ve_learn_conf=00 lcd_c0=FE lcd_delay=FF lcd_backlight=FF lcd_offs[0]=FF lcd_offs[1]=FF lcd_offs[2]=FF lcd_offs[3]=FF lcd_default_view=00 primary_trigger=01 secondary_trigger=FF Should be 02 if no trigger is used tooth_wheel=3A trigger_tooth=10 another_trigger_tooth=14 crank_minper=50 tooth_wheel_twidth1=06 tooth_wheel_twidth2=12 cam_sync_r_edge_phase=FF cam_sync_f_edge_phase=FF reset_engphase_after=FF ign_tdcdelay=70 ign_dwell14=30 ign_dwell6=83 ign_crank_advance=00 ign_out=70 ignchmax=01 engine_off_delay=08 pump_on_mintime=10 fuelpump_channel=P259_5 inj_stage2_rate=FF inj_stage2_start_tps=FF inj_stage2_start_map=FF als_lowrpm=FF als_maxtps=FF als_ignretard=FF als_rich=FF als_rev_limit=64 misc1out_minrpm=06 misc1out_maxrpm=19 misc1out_mintps=20 misc1out_maxtps=FF misc1out_minmap=50 misc1out_maxmap=FF misc1out_channel=FF misc2out_minrpm=FF misc2out_maxrpm=FF misc2out_mintps=FF misc2out_maxtps=FF misc2out_minmap=FF misc2out_maxmap=FF misc2out_channel=FF act_wot_rpm=FF act_wot_channel=26 act_rpm_rpm=FF act_rpm_channel=FF egt1_cal=40 egt1_offs=00 boost_conf=00 boost_targetoffs=00 boost_minpressure=FF boost_pid_kp=20 boost_pid_ki=80 boost_pid_kd=01 boost_pid_ilimit=FF boost_channel=FF water_pump_temp=00 hybrid_rpm_a=00 hybrid_rpm_m=00 water_pump_hyst=00 water_pump_channel=FF toothrel_normal=B5 toothrel_missing=76 fuelcut_kpa=7F </code> [[! MembersPage/RobertOffner]]
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.