______ 
|  ___|
| |_   
|  _|  
| |    
\_|    
       
       

    ##   
         
    ##   
    ##   
    ##   
    ##   
    ##   
  ###    

         
|\     /|
( \   / )
 \ (_) / 
  \   /  
   ) (   
   | |   
   \_/   
         

 _______ 
(  ____ \
| (    \/
| (__    
|  __)   
| (      
| (____/\
(_______/
         

         
     ##  
     ##  
  #####  
 ##  ##  
 ##  ##  
  #####  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Location:''' Stockholm, Sweden ---- '''Buylist''' MemebersPage/RobertAdolfsson/Buylist *Main components: **1 x GenBoard v3.3 **1 x Dual channel knock sensor interface **1 x EGT input amplifier **1 x Idle stepper motor driver **4 x Ignition driver **10 x Injector or WBO2 heater driver **1 x Power Flyback **1 x Econoseal18-PCB **1 x Econoseal36-PCB *Sensors etc: **1 x 400/250 kPa MAP sensor **2 x Pneumatic tube **1 x Pneumatic connector **1 x Wideband O2 sensor **1 x Wideband connector **1 x EGT sensor (K-type) **2 x K-compensational cable **1 x K-thermocouple connector **1 x Econoseal18-Wire **1 x EconoSeal36-Wire *Extras: **1 x LCD4x20 **3 x clamping plate **2 x Alubos gasket **1 x Alubos Endplate **1 x Alubos EC frontplate **1 x Alubos1600 **4 x Injector connector **4 x Injector connector **1 x VEMS sticker **1 x Ignition driver insulator sheet Did i miss anything? It should be sufficent for 4 cyl directfire, wideband O2, 8 injectors and boost control in my mind. I haven't yet decided if I should try to fit it inot a LH 2.4 box but I'll by the Alubos1600 anyway. ---- I'm planning to implement Genboard V3.3 on my Volvo 745 '90. ---- '''Current specification:''' * The engine is a rebuilt standard B230FT (Original engine). ** 2319 cc, 96.3 mm bore, 80 mm stroke. * Forged pistons (Venolia) * Forged H beam con rods (SPM) * "O-ring" sealings between cylinder head and engine block * Oil cooled pistons ** was not standard until 1993 on B230FT... * Larger "gourp A" oil gasket with internal hatches * Uprated oil pump * 531 cylinder head ** almost same as the standard cylinder head head but with "better" intake side that allows better air flow. * "Larger" turbo, Schnitzer. Don't remember the specs for it. ---- '''Plans:''' * Use original harness as much as possible * Use original sensors * Extend the harness to acommodate directfire, cam angle sensor, wide band lambda, etc. ---- '''Questions:''' * The original crank sensor is a 60-2 hole VR sensor arrangement. I guess that the original LH 2.4 ECU doesn't have the filtering circuit on board but some external filtering circuit which generates a TTL "home" signal for every revolution of the crank shaft. I need to find this and decide wether to omit this totally and use the VR sensor option of GenBoard or use it and configure the Genboard apropriately. ** I guess this circuit has 2 outputs. Record both outputs, one at a time with the original 60-2 signal connected to the other channel (scope with probe in 10x divider mode, or PC soundcard with 100k and 1k voltage divider to divide signal to 1/100) * The cam angle sensor could be implemented by obtaining an older distributor for the LH 2.2 (or maybe motronic) from an older 740 which used a hall sensor with 4 signals to control the ignition. By modifying the distributor, this could be changed to give the apropriate cam "home" signal. ** before grinding, draw and plan in wiki, so someone can help confirm the position (preferrably the falling edge of the HALL signal is used, and in current firmware there is some restriction on the position of the cam signal (chosen edge)) ---- '''TODO:''' * Find out what is needed in terms of components * Buy a Genboard
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.