##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 #####   
         

______ 
|  _  \
| | | |
| | | |
| |/ / 
|___/  
       
       

_________
\__    _/
   )  (  
   |  |  
   |  |  
   |  |  
|\_)  )  
(____/   
         

         
         
  ### #  
 #   ##  
 #   ##  
  ### #  
      #  
      #  

         
  #####  
 ##  ##  
 ##      
 ##      
 ##   #  
  ####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Plug'n'play was a nice idea, but connectors are harder to find. A new ECU and a new loom to suit is easier. Land Rover made life good for us and used injector connectors on most everything, so hook up is easy - really only needed to fit the MAT sensor to intake pipe. ---- Pin mapping: ||'''Function'''||'''VEMS ECU pin'''||'''Wire Colour'''||'''Comments'''|| ||||||||''Power''|| ||Vbatt||EC36-25||Red|| || ||Ground||EC36-26||Black||Direct to battery for lowest noise|| ||Power Ground||EC36-21 EC36-32 EC36-5||Black||Good connections!|| ||||||||''Inputs''|| ||Trigger||EC36-27||White||Shielded, see notes below|| ||TPS||EC36-1||Green|| || ||TPS Vref||EC36-28||Red|| || ||TPS Gnd||EC36-5||Yellow|| || ||Coolant temperature||EC36-14||Blue|| || ||Manifold air temp||EC36-2||Grey|| || ||||||||''Outputs''|| ||Fuel pump relay -ve||EC36-15||Orange||P259_5|| ||Cooling fan relay -ve||EC36-4||Green||P259_0|| ||Injector 1||EC36-7||Black|| || ||Injector 2||EC36-19||Black|| || ||Injector 3||EC36-8||Black|| || ||Injector 4||EC36-20||Black|| || ||Injector 5||EC36-9||Black|| || ||Injector 6||EC36-18||Black|| || ||Injector 7||EC36-6||Black|| || ||Injector 8||EC36-17||Black|| || ||Idle stepper A||EC18-4|| || || ||Idle stepper B||EC18-10|| || || ||Idle stepper C||EC18-5|| || || ||Idle stepper D||EC18-11|| || || ||||||||''WBO2''|| ||Nernst||EC36-13||Black||Oops, should have been shielded|| ||Pump +||EC18-9||Red|| || ||Pump -||EC18-7||Yellow|| || ||Heater +||-||Grey||to fuse block|| ||Heater -||EC18-18||White|| || ||||||||''Comms''|| ||RS232 rx||EC18-|| ||Shielded|| ||RS232 tx||EC18-|| ||Shielded|| ||RS232 gnd||EC18-|| ||Shielded|| The new loom is constructed from Automotive-spec Cross-linked Polyethelene wire (-40 to 125 degrees centigrade) and Military-spec Tefzel wire (-65 to 150 degrees centigrade). Fuses and relays are automotive, for easy replacement if and when required. * SAE-J1128 TXL cross-linked polyethelene wire for all except the following: ** MIL-27500 shielded 1 conductor Tefzel for the trigger --and WBO2 nernst signals--. ** MIL-27500 shielded 3 conductor Tefzel for the serial communication cable. '''Trigger notes''' Given that the Mallory is a multi-spark unit, we don't want to read from the coil. We'll use the 12V square wave signal from the Mallory ignition tach output. What's the best way to cut this down to a 5V squarewave that will work with the ECU using the Hall configuration? Should we use an MS-esque opto-coupler externally? Perhaps like this: [http://vems.hu/files/MembersPage/RichardBarrington/Capri/optotrigger.png http://vems.hu/files/MembersPage/RichardBarrington/Capri/optotrigger-small.png] ---- Back to MembersPage/RichardBarrington/TonysCapri Back to MembersPage/RichardBarrington
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.