####   
     ##  
  #####  
 ##  ##  
  #####  
         

         
         
  ### #  
 #   ##  
 #   ##  
  ### #  
      #  
      #  

  ______
 |___  /
    / / 
   / /  
  / /__ 
 /_____|
        
        

  _____ 
 |  ___|
 | |_   
 |  _|  
 |_|    
        

 ___   
(  _`\ 
| (_(_)
|  _)_ 
| (_( )
(____/'
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Hello, I own 1991 '''Audi''' S2 coupe with '''2,2L 5syl 3B engine''', and my main goal is to make it run on VEMS and get power between 350-400BHP. Right now my best ET at 1/4 mile is 12,82 seconds. ---- '''Engine''' * big intercooler with opposite direction air flow, by-pass in new location and drilled intake manifold. * Intake: AEM 4" air filter * original K24 7000 turbo ** I recommend some uptodate turbo design (garret ?) not K26/27 like MembersPage/MarcellGal/PowerAndTraction where turbo wakes up a bit late (above 4200 RPM in gear 2) for the power (406 Hp) * Exaust: RS2 manifold, wastegate wiht stronger spring (old 10VT audi one), stock downpipe, straight through pipe to last original silencer. * Fuel: stock fuel pump but modified elecrical system, mallory FPR. * Gauges: VEMS Round WBO2 and EGT (2mm EGT sensor, RPM input, analog input for boost, analog output for stock ECU NB lamda), boost. VemsAudiAan shows a straightforward wiring recipe for this engine, wether * using motronic ECU ** still needs some wiring, eg. WBO2 * using v3harness * or building custom harness ** best fit, but most work and likely the most costly as well for ignition upgrade, you can either go distributerless, eg.: * apply a 2x2 wasted spark module to drive ign2,5 and ign3,4 like MembersPage/MarcellGal/PowerAndTraction (ign1 driven by factory ign transformer) * apply AAN-type ignition: power output stages + transformers ** or without power output stages, just the transformers (driven with power "IGBT" output, of course) * use 5 logiclevel COPs (not recommended, these COPs don't live long in high performance engines) * or use 1 channel CDI and keep the distributer (make sure it is positioned well, especially if using ALS - not recommended though) '''The most appropriate ECU''': * assembled v3.x * 6 IGBTs + 2 logiclevels ** write in the order note: "255 Ohm logiclevel output" to allow even for the (otherwise not recommended logiclevel COPs) ** with the 4 stepper channels, this allows up to 6 logiclevel and 6 power outputs * no 1 wire * 30V flyback * primary trigger=VR * secondary trigger=auditrigger * 300 kPa internal MAP sensor ** or 400 kPa, but without serious internal engine upgrade higher than 1.8 bar boost is not feasible anyway * no screws (easier to mount in the audis without screws) ---- '''Chassis''' Brakes: 4x zimmerman discs, ferodo brake pads, Motul RBF600 brake fluid. Front brakes are waiton for upgrade, alredy buyed wilwood 4 piston calipers and audi A8 320mm discs. Suspension: 4x kony yellow shocks, original springs are wating for lowering ones. Body: The car got new paint a year ago, for better cooling it has modified RS2 replica front bumper, a little wider rear bumper, loesed lower door covers, tinted windows. Other: 034 short shifter ---- '''Plans:''' * Need to change the 2mm EGT sensor with 6mm one. ** especially if the sensor is before the turbo (although I guess it is after the turbo, in the manifold in the factory place) * Bigger MAP sensor for boost logging. * Change the ingniton system and eventually VEMS ecu (this takes for some time). ---- Turbo update is already in my plans, garret GT3071r i think, but all this comes with VEMS ECU. The EGT sensor replacement is becase it is now in manifold, wiht old manifold it was after the turbo. ---- Today I started to "play" with boost logging option. First i needed to measure voltage @ different pressure points. I had precise boost gauge and compressor with variable output. I connected the gauge to compressor and started to measure difrent pionts with stepping 10kPa at 100kPa to 200kPa (200kPa is orginal boost MAP) now i writed all the numbers and from them calculated average step (31,5), thats what I came up: At athmospheric pressure it shows @gauge 1300 @ 0kPa - 985 @ 10kPa - 1016,5 @ 20kPa - 1048 @ 30kPa - 1079,5 @ 40kPa - 1111 @ 50kPa - 1142,5 @ 60kPa - 1174 @ 70kPa - 1205,5 @ 80kPa - 1237 @ 90kPa - 1268,5 @ 100kPa - 1300 @ 110kPa - 1331,5 @ 120kPa - 1363 @ 130kPa - 1394,5 @ 140kPa - 1426 @ 150kPa - 1457,5 @ 160kPa - 1489 @ 170kPa - 1520,5 @ 180kPa - 1552 @ 190kPa - 1583,5 @ 200kPa - 1615 Gauge settings ate: linear curve, calibration is 255, offsett is 0 From all that I generated formula to get kPa for logging: ( value - 985 ) / 3.15 and inserted it to the round.ini file. This log file shows that everything should work fine: http://ranz.planet.ee/S2/logi.JPG
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.