####   
 ##  ##  
 ######  
 ##      
  ####   
         

   _____ 
  / ____|
 | |  __ 
 | | |_ |
 | |__| |
  \_____|
         
         

     ##  
     ##  
  #####  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
         

  _____  
 |  __ \ 
 | |__) |
 |  _  / 
 | | \ \ 
 |_|  \_\
         
         

  ____  
 |  _ \ 
 | |_) |
 |  _ < 
 |_| \_\
        

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Hello, I own 1991 '''Audi''' S2 coupe with '''2,2L 5syl 3B engine''', and my main goal is to make it run on VEMS and get power between 350-400BHP. Right now my best ET at 1/4 mile is 12,82 seconds. ---- '''Engine''' * big intercooler with opposite direction air flow, by-pass in new location and drilled intake manifold. * Intake: AEM 4" air filter * original K24 7000 turbo ** I recommend some uptodate turbo design (garret ?) not K26/27 like MembersPage/MarcellGal/PowerAndTraction where turbo wakes up a bit late (above 4200 RPM in gear 2) for the power (406 Hp) * Exaust: RS2 manifold, wastegate wiht stronger spring (old 10VT audi one), stock downpipe, straight through pipe to last original silencer. * Fuel: stock fuel pump but modified elecrical system, mallory FPR. * Gauges: VEMS Round WBO2 and EGT (2mm EGT sensor, RPM input (signal from ECU wire, setting 5 and 229), analog input for boost (settings below), analog output for stock ECU NB lamda), autogauge boost. VemsAudiAan shows a straightforward wiring recipe for this engine, wether * using motronic ECU ** still needs some wiring, eg. WBO2 * using v3harness * or building custom harness ** best fit, but most work and likely the most costly as well for ignition upgrade, you can either go distributerless, eg.: * apply a 2x2 wasted spark module to drive ign2,5 and ign3,4 like MembersPage/MarcellGal/PowerAndTraction (ign1 driven by factory ign transformer) * apply AAN-type ignition: power output stages + transformers ** or without power output stages, just the transformers (driven with power "IGBT" output, of course) * use 5 logiclevel COPs (not recommended, these COPs don't live long in high performance engines) * or use 1 channel CDI and keep the distributer (make sure it is positioned well, especially if using ALS - not recommended though) '''The most appropriate ECU''': * assembled v3.x * 6 IGBTs + 2 logiclevels ** write in the order note: "255 Ohm logiclevel output" to allow even for the (otherwise not recommended logiclevel COPs) ** with the 4 stepper channels, this allows up to 6 logiclevel and 6 power outputs * no 1 wire * 30V flyback * primary trigger=VR * secondary trigger=auditrigger * 300 kPa internal MAP sensor ** or 400 kPa, but without serious internal engine upgrade higher than 1.8 bar boost is not feasible anyway * no screws (easier to mount in the audis without screws) ---- '''Chassis''' Brakes: 4x zimmerman discs, ferodo brake pads, Motul RBF600 brake fluid. Front brakes are waiton for upgrade, alredy buyed wilwood 4 piston calipers and audi A8 320mm discs. Suspension: 4x kony yellow shocks, original springs are wating for lowering ones. Body: The car got new paint a year ago, for better cooling it has modified RS2 replica front bumper, a little wider rear bumper, loesed lower door covers, tinted windows. Other: 034 short shifter ---- '''Plans:''' * Need to change the 2mm EGT sensor with 6mm one. ** especially if the sensor is before the turbo (although I guess it is after the turbo, in the manifold in the factory place) * Bigger MAP sensor for boost logging. * Change the ingniton system and eventually VEMS ecu (this takes for some time). ---- Turbo update is already in my plans, garret GT3071r i think, but all this comes with VEMS ECU. The EGT sensor replacement is becase it is now in manifold, wiht old manifold it was after the turbo. ---- Setting up analog in to read it from gauge or log it: S2 3B original 200BAR MAP I connected my compressor variable output (with gauge: 0 to 2,5BAR) directly to MAP input. User z0tya from forum gave me somekinde of numbers what he calculated, I inserted them and started to play with them. Calibration setting 32, offset 0 First I needed to get 100 reading at atmosphere pressure, I changed numbers at analog in to get it. Now raised compressor oputput to 0,5BAR and played with numbers to get reading 150, then output to 2BAR and played to get 200. After that tested other readings, 0,1BAR - 110, 0,2BAR - 120, 0,3 - 130 etc. I din't have to change any more numbers at analog in curve becase it was enough only measure 3 points (0BAR - 1,5BAR - 2BAR). These are numbers from analog in curve: 0 - 0 1 - 0 2 - 0 3 - 0 4 - 0 5 - 0 6 - 0 7 - 0 8 - 18 9 - 30 10 - 55 11 - 106 12 - 145 13 - 180 14 - 220 15 - 225 16 - 240 First 7 rows are 0 becase they din't change the reading, also are 15 and 16 set to linear in because they din't cange nothing also. Now i borrowed my friends ECU what has 300BAR MAP and did the same thing. Calibration 64, offset 0 Measured 5 points (0 - 0,5 - 1 - 1.5 - 2BAR) to get right reading (played vith analog in curve) and other readings between measured points where rigt also. These are numbers from this analog in curve: 0 - 0 1 - 0 2 - 0 3 - 0 4 - 0 5 - 0 6 - 0 7 - 0 8 - 5 9 - 15 10 - 41 11 - 74 12 - 106 13 - 136 14 - 169 15 - 225 16 - 240 First 7 and 2 last are same as it was previously. Now i'm wating my order from vems and when my stuff arrives, I'll measure the VEMS 300BAR MAP also. Log file (RPM spikes are things what I can't get rid of): http://ranz.planet.ee/S2/logi.JPG It shows also that original turbo is small :P boost rises to 1,6BAR and then drops down again, also the A/F is not wery good (soft is for RS2 injectors, I'll try them later).
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.