_    
    / \   
   / _ \  
  / ___ \ 
 /_/   \_\
          

 _       
| \    /\
|  \  / /
|  (_/ / 
|   _ (  
|  ( \ \ 
|  /  \ \
|_/    \/
         

 _   __
| | / /
| |/ / 
|    \ 
| |\  \
\_| \_/
       
       

         
         
  ####   
     ##  
  #####  
 ##  ##  
  #####  
         

         
    ###  
   ##    
  #####  
   ##    
   ##    
   ##    
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD Start] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FQuestions Questions ] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FInjector Injector] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FIgnition Ignition] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FTrigger Trigger] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FDisplay Display] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FWbo Wbo] ||[http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FConfig Config] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FTables Tables ] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FIdle Idle] || '''WBO2 sensor information''' * Bosch LSU4 sensor ---- '''Relevant WBO2 parameters:''' wbo2_warmup_ramp=A0 wbo2_abs_limit=2A wbo2_limit_maxt=A0 wbo2_fallback=60 wbo2_retry_t=06 wbo2_ri_target=96 wbo2_nernstdc_target=89 wbo2_pump_pw_zero=64 wbo2_calibration=B9 wbo2_heater_pid_kp=45 wbo2_heater_pid_ki=11 wbo2_heater_pid_kd=1A wbo2_heater_pid_ilimit=81 wbo2_pump_pid_kp=15 wbo2_pump_pid_ki=4E wbo2_pump_pid_kd=00 wbo2_pump_pid_ilimit=FF wbo2_ri_confidence_scale=80 ---- '''Previous problems to learn from: 12SEP2007''' My O2% value wouldn't read over 16.0%, not even with wbo2_calibation =0xFF. The problem was that for some reason wbo2_abs_limit was set to 0x00, preventing the sensor from heating properly. Once increased it was possible again to correctly calibrate the sensor in free air with wbo2_calibration parameter.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.