##  ##  
 ####### 
 ## # ## 
 ##   ## 
 ##   ## 
         

 #       
 #       
 # ###   
 ##   #  
 #    #  
 ##   #  
 # ###   
         

   _____ 
  / ____|
 | (___  
  \___ \ 
  ____) |
 |_____/ 
         
         

         
         
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
    ##   
 ####    

   _____ 
  / ____|
 | |     
 | |     
 | |____ 
  \_____|
         
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD Start] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FQuestions Questions ] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FInjector Injector] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FIgnition Ignition] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FTrigger Trigger] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FDisplay Display] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FWbo Wbo] ||[http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FConfig Config] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FTables Tables ] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FIdle Idle] || '''60-2 no camsync, 4 cylinder''' using firmware 1.1.12 * batch injection * wasted spark ignition * stock Peugeot (Magneti Marelli?) VR sensor (3 wire) http://img339.imageshack.us/img339/196/flywheeltimingsmallwr3.png Trigger timing is as shown in the picture. Running direction is Counter Clockwise (wrt picture), 1st and 4th cylinder are at TDC. BTDC = 120 degrees. \\ \\ '''Relevant trigger parameters:''' primary_trigger=01 secondary_trigger=02 tooth_wheel=3A trigger_tooth=0A another_trigger_tooth=1E crank_minper=50 tooth_wheel_twidth1=18 (decimal 24, that is 6 degrees) tooth_wheel_twidth2=48 (decimal 72, that is 18 degrees) ign_tdcdelay=78 ign_crank_advance=12 ign_out=70 ignchmax=03 h[0]=0F 00 00 00 00 00 00 00 h[2]=00 10 00 10 00 10 00 10 ---- '''Previous problems to learn from:''' I had issues with the triggering of the engine. The engine didn't run properly when set up for 120 degrees (trigger_tooth=0A and ign_tdcdelay=0x78; 10*6 + 120*0.5 = 120 degrees)). Remarkely it did run when setup for 60 degrees. Although it is not clear what exactly caused the timing problem, after using [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPhatBob%2FALSConfigFix ALSfix] my problem was over and the engine started with the correct timing.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.