###    
   ##    
   ##    
   ##    
   ##    
  ####   
         

         
### ##   
 ### ##  
 ##  ##  
 ##  ##  
 ##  ##  
#### ### 
         

     ##  
     ##  
  #####  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
         

 ___   
(  _`\ 
| (_(_)
|  _)  
| |    
(_)    
       
       

         
         
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
    ##   
 ####    

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD Start] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FQuestions Questions ] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FInjector Injector] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FIgnition Ignition] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FTrigger Trigger] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FDisplay Display] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FWbo Wbo] ||[http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FConfig Config] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FTables Tables ] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FRallyeNLD%2FIdle Idle] || Running questions and trouble ---- '''60-2 no camsync, 4 cylinder''' using firmware 1.0.69 * batch injection ** why don't you run the 4 injectors at different times from 4 outputs (and only use batch during cranking) * wasted spark ignition. Relevant config: primary_trigger=01 secondary_trigger=02 tooth_wheel=3A trigger_tooth=02 another_trigger_tooth=1E * BAD: crank_minper=EA (might get you unintentianal revlimit) ** crank_minper=00 will do fine * BAD: tooth_wheel_twidth1=02 ** tooth_wheel_twidth1=18 (decimal 24, that is 6 degrees) * BAD: tooth_wheel_twidth2=06 ** tooth_wheel_twidth2=48 (decimal 72, that is 18 degrees) * BAD: ign_tdcdelay=D8 ** use 55 .. 65 degrees, and adjust trigger_tooth accordingly ign_crank_advance=12 ign_out=70 * ignchmax=01 ** prefer ignchmax=03 h[0]=0F 00 00 00 00 00 00 00 h[2]=00 10 00 10 00 10 00 10 The '''first (zeroth if you like) tooth after the''' missing tooth occurs (at the sensor) 120 degrees (???) that is 20 teeth BTDC. Verify this! It's not the middle of the missing tooth that counts. * BAD: trigger_tooth=02 and ign_tdcdelay 0xD8 (216 * 0.5 = 108 degrees). The sum would be good: 12 + 108 = 120 degrees but timing from a tooth too early is not good (especially during cranking) ** good: trigger_tooth=0A and ign_tdcdelay=0x78 (10*6 + 120*0.5 = 120 degrees) Now the engine won't start and will kick back during cranking. For some reason I tried ign_tdcdelay = 0x5A (90 * 0.5 = 45 degrees). Together with trigger_tooth this makes 12 + 45 = +- 60 degrees) which happens to be half the real value of 120 degrees. The engine is running sweet then, especially at increased engine revs. Q. Although the engine is running I would like to know what mistake I made. Did I use the wrong factor (2 instead of 0.5) or something else is wrong. * can you strobe the engine ? * maybe the angle is not 120 degrees ? ** do you count from the proper point ?
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.