###  
   ##    
  #####  
   ##    
   ##    
   ##    
         

 _       
( \      
| (      
| |      
| |      
| |      
| (____/\
(_______/
         

         
         
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
         

_________
\__    _/
   )  (  
   |  |  
   |  |  
   |  |  
|\_)  )  
(____/   
         

         
   ##    
         
  ###    
   ##    
   ##    
  ####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Car is Audi S4 Avant 93' with 2.2T AAN engine. Basic info: stock pistons h-beam rods 1200cc EV12 injectors HX40Super 14# tubular manifold 600x300x76 IC 3.5" DP and exhaust to the end Using E85 as fuel fuel supply: two bosch 044 Power figures at the moment: 2.3bar boost -> 545hp and 600Nm from wheels Plug n Play Vems motronic v3.6 ------- I was wondering if is it possible to log 5 egt sensors with my vems? Or maybe someone knows some good equipment for this? Thanks Risto ------- On 1 november 2010 the car went to dyno. It made 450hp an 540 nm from wheels. The resluts are little bit modest because one 044 bosch fule pump just can keep up with 80lb/h injectors and holset. Now i need to put two additional fuel pumps with surge tank, just to be sure. Lets hope 520hp and 650nm from wheels will be then achievable. PS! The car is running now PnP Vems motronic V3.6. ------- The car works and no trigger errors has been recorded so far (driven for about 150km). The problem was that i am using Fidanza ALU flywheel. It has to small trigger for the VR sensor. It has to be bigger. Second thing were the bolts on the flywheel that hold the toothed to the flywheel. These bolt are made for regular steel. These must be changed to stainless steel or smth else that dosent react to magnet. Also the hall sensor (near the firewall) must be in it's original markings. After doing these little "improvments" the car started. Now it needs to be tuned correctly and then i can enjoy my car. :) Let's see how much power and torque will the holset HX40Super give my dailydriver. ---- '''relevant * what is the history of the controller ? ** Is it an econoseal or motronic55 ? ** Serialnr ? * With what options was it ordered ? ** nr of IGBTs ? * what modifications were done ? ** besides the home-installed AudiTrigger/CamHALLInverter).. ** ... ? * Did the engine work before ? * How are you sure that the used ign outputs are logiclevel ? ** Do the ign outputs (when power output stages are disconnected) measure -12V when measured from +12V as a base ? (ign on, but engine off) We will verify your ign outputs when we see ign outputs in your config+tables ( h[2] ) * I see the wiring http://gph.planet.ee/vems/RST/ but that's just one half of the story The ignition can be spark-tested with Man mdn00 mdn04 mdn03 mdn02 mdn01 (also from the ignition outputs dialog in new VemsTune). * For all high-voltage ignition ("ign transformer secondary") wires make sure there is return path to engine head, eg. sparkplug thread touches ground. ** Don't electrocute yourself or the controller. ---- * Car doesn't start. it gives something like 5 misfires for 6-10 sec starting. * When I tried without HALL inverter the engine gave some backfires but still not started. * If the HALL signal and Flywheel triger wasn't aligned correctly the engine sometimes started. The setup uses HALL trigger from distributor. The HALL signal is inverted. (home-installed AudiTrigger/CamHALLInverter). Measure voltage BEFORE and AFTER the inverter (during cranking) * I measured it with scope and it's ok. The trigger_tooth=08 is good for * factory HALL window position WITHOUT camHALL inverter * or HALL window 180 camdegrees offset, WITH camHALL inverter ** Marcell has such setup working on his 3B. Note that ignout=cyl5 cyl4 cyl2 cyl1 cyl3 ... applies for that ! We MUST see your ignition output configuration as well (and reference trigger tooth array). Publish the mct dump (the tables are best, make a screenshot at a minimum) * The wiring diagram is on the link: http://gph.planet.ee/vems/RST/
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.