# # # # # # # # ##
_ | | | | _ | | | |__| | \____/
### # # ## # ## ### # # ####
_____ (___ ) | | _ | | ( )_| | `\___/'
____ | _ \ | | | | | |_| | |____/
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: Hello my name is Quincy Straker. I live in the Netherlands and I study Automotive on University (bachelor). I am building a Suzuki gsxr-1100 with Hayabusa throttlebodies and COP, T3/T4 Turbo, external wastegate and ofcourse VEMS. A very interesting project! I am investigating how to install on a Suzuki GSX-R 1000 (year 2001), it's very likely there are similarities. ******WEBSHOP PARTS * Pneumatic valve 3way, * Bosch knock sensor, * Coolant sensor AMP-connector * EGT sensor (K-type) * - Size: 6mm * Fuel Pressure Sensor * HALL sensor * K-compensational cable * MAT sensor * K-thermocouple connector * Sex: pair mounting-style: panel-mount * Wideband connector * With wire: with crimped wires * Wideband O2 sensor * Wideband screw * LCD4x20 * Color: green * Assembled v3.3 controller * 1-wire interface: yes * ignition driver: 4 * Knock and EGT: knock and 2 EGT * LCD and PS2: yes * MAP connection: 400kPa onboard (6/4mm pneumatic) * mounting-style: screws * PowerFlyback: yes * primary_trigger: HALL * secondary_trigger: HALL * v3harness * Automotive Relay * with_socket: yes ******ENGINE SETUP * 1100 cc (carburated) motorcycle engine * Carburator replaced with trottle bodies from a Hayabusa. * 8 hayabusa injectors. * Custom intakemanifold. * T3/T4 T04e turbo. * Aeromotive fuel pressure regulator. * Walbro 255 l/h fuel pump. * forged pistons and rods. * 12-1 triggerwheel * Hayabusa Coil on plugs ******GENBOARD SETUP * firmware 1.0.73 * Board version=v3.3 * Serial_nr=856 * pump-=4.13V * wb02_pump_pw_zero=0x67 * wb02_nernstdc_target=0x86 * pump+=-2.5mV/200 Ohm * AREF=4.9V * (C103=1nF, no D100) Memberpage/QuincyStraker/InputTrigger Memberpage/QuincyStraker/InjectioN Memberpage/QuincyStraker/IgnitioN Memberpage/QuincyStraker/ConfIg Memberpage/QuincyStraker/TabLes Memberpage/QuincyStraker/Wiring http://i196.photobucket.com/albums/aa262/shushu4345/02072007588.jpg http://i196.photobucket.com/albums/aa262/shushu4345/02072007590.jpg http://i196.photobucket.com/albums/aa262/shushu4345/02072007586.jpg http://i196.photobucket.com/albums/aa262/shushu4345/02072007585.jpg http://i196.photobucket.com/albums/aa262/shushu4345/02072007584.jpg http://i196.photobucket.com/albums/aa262/shushu4345/02072007583.jpg ---- '''Ignition outputs''' * If I use Coil on plugs, do I need to put the ignition setting on edis or dummy? ** "dummy", of course You should start from a working setup (of a missing tooth trigger). ---- '''12-1 trigger''' * the wheel I made is 15 degree missing tooth and 15 degree tooth (width) ** you misunderstand the terms. The toothwidth is 30 degrees (and missing tooth width would be 60 degrees, but it's not specified now) For 12-1 use * angular width of tooth=120 (30 degrees) * angular width of missing tooth = 0 ** it is actually the upper byte of normal tooth-width, nothing to do with missing tooth (this label in older MegaTune is outdated now) * primary_trigger=11 missing tooth wheel, N-1 enabled, rising edge ** or primary_trigger=10 missing tooth wheel, N-1 enabled, falling edge (only allowed for HALL) '''1.0.7x firmware is recommended''' * 1.1.27 should also work, just requiring more settings (without much advantage for this wheel). Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.