####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  ####   
         

         
         
 # ###   
 ##   #  
 #       
 #       
 #       
         

 _____ 
|  _  |
| | | |
| | | |
\ \_/ /
 \___/ 
       
       

         
         
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
         

 ___   
(  _`\ 
| (_(_)
|  _)_ 
| (_( )
(____/'
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
I have a Dax Rush with Rover V8 engine. The Rush is a kit car derivation off the Lotus Super 7. The car’s primary function is a fun toy to make me smile. It is used on the road and track whenever I find time. The current set-up Suspension and wheels: The wheels are 205/40/17 front and 245/40/17 at the back. Suspension is unequal length dual wishbones front and live axle back and adjustable coil over shocks all around. Brakes: Front 240mm vented disks with Wilwood 4 pot callipers, back is Ford Sierra disks with callipers. Hand brake via cable to the rear callipers. Engine: The current engine is a Rover 3.9 V8. It has been prepared by V8tuner in 2002. I will replace the engine with a Rover V8 4.6 that is waiting in my garage for the exchange. The 4.6 will have stage 3 big valve 28cc heads, a Kent camshaft (218-234?) with hydraulic Rhodas lifters and adjustable push rods. Oil supply is dry sump and 3 stage pump, remote filter and oil cooler. The dry sump set-up helps with the oil starvation problems due to acceleration or cornering. Ignition: The ignition set-up has not yet been decided but will be most likely wasted spark with crank trigger wheel. Fuel injection: It will be a modified standard Rover plenum and manifold. I intend to shorten the thrumpets and lower the plenum height to get a better fit. I will still need a hole in the bonnet and the plenum will stick out. But the intake piping should then go under the bonnet! Transmission: The current gearbox is the Rover LT77 5 speed. I might replace it with the same box taken from a fright Sherpa Van. This box has allegedly stronger components fitted. Only drawback is the short first gear ratio of 3.985 : 1 that is way to short for the Rush. The flywheel is an aluminium one with a strong Sachs clutch, all rated for 350BHP. At the back I have a 4 link Atlas live axle with Panhard Rod. Final drive ratio of the axle is 3.09 : 1 The car is around the 680kg mark. That makes for some mind-boggling acceleration. Wheel spin by changing from 2 to 3 is possible. In the dry! The top speed is nothing to write home about. I have never had it flat out yet. My assumption is in the region of 140 mph. The aerodynamics of the Rush is equal to a brick. The 3.9 engine was measured on RR with 235 BHP. I am looking for 270 BHP and 400Nm torque from the 4.6 engine. Those are real figures not the claimed +300 BHP that you often see. I have a centrifugal supercharger (Powerdyne BD11) waiting in my garage as well. The trouble is, I have not found the space in the engine bay to fit the thing. I am thinking of using a grinder and MIG welder to create the space. But that will be later.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.