___ 
 |_ _|
  | | 
  | | 
 |___|
      

         
         
  ####   
 #    #  
 #    #  
 #    #  
  ####   
         

         
         
  ####   
 ##  ##  
 ######  
 ##      
  ####   
         

  ____  
 |  _ \ 
 | |_) |
 |  _ < 
 |_| \_\
        

         
         
 ######  
 #  ##   
   ##    
  ##  #  
 ######  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen Start]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen%2FQuestions Questions ]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJenseninjector Injector] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenignition Ignition] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensentrigger Triger] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenDisplay Display] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenWbo Wbo2]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenconfig Config] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensentable Table] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenwiring Wiring] || When we calibrate the wbo2 sensor we need to change values in wbo2 config. [http://vems.sourceforge.net/manualhtml2/ch07s02.html manual] 1: calibrate (wbo2_pump_pw_zero) measure the voltage between pins 5 and 6 of the wideband connector The ideal voltage is so cloce to zero (0) as passebele. To adjust the voltage, change the value of wbo2_pump_pw_zero in config.txt or Megatune. A good starting point value should be between 0x64 to 0x66 decimal 100 – 102. 2: Place a 100 Ohm resistor between pump+ (pin 6) and nernst (pin 1) 3: Place a 100 Ohm resistor between pump- (pin 5) and nernst (pin 1) 4: Open the terminal program 5: Turn on the WBO2 heater by typing “Man” then “mde02” then “mlp07” to get to the wbo2 page at the display.DUE NOT CONNECT THE WBO2 SENSOR YET 6: Measure the voltage between ground and pump- (pin 5). It should read 3.96V. Measure the voltage between ground and nernst (pin 1). It should read 4.41V. Measure the voltage between nernst (pin1) and pump- (pin 5). It should read +450mV. 8: The ajustment can be don from mega tune IF SOME ONE CAN HELP WITH THE NEXT STEP 8: To adjust the voltage between ground and pump- (pin 5).= Tag ??? To adjust the voltage voltage between ground and nernst (pin 1).= Tag ??? adjust nernst_dc_target if that due not worke then ?? To adjust the voltage between nernst (pin1) and pump- (pin 5).0 Tag ??? http://www.vems.hu/files/PeterJensen/wbo2imag/wbo_1.jpg http://www.vems.hu/files/PeterJensen/wbo2imag/wbo_2.jpg wbo2 wbo2_warmup_ramp=31 wbo2_warmup_target=FF wbo2_abs_limit=A0 wbo2_limit_maxt=FF wbo2_fallback=60 wbo2_retry_t=02 wbo2_edgetime_corr=BA wbo2_edgetime_min=50 wbo2_ri_target=96 wbo2_nernstdc_target=98 wbo2_pump_pw_zero=64 wbo2_calibration=A9 wbo2_heater_pid_kp=45 wbo2_heater_pid_ki=11 wbo2_heater_pid_kd=1A wbo2_heater_pid_ilimit=81 wbo2_pump_pid_kp=15 wbo2_pump_pid_ki=4E wbo2_pump_pid_kd=00 wbo2_pump_pid_ilimit=FF wbo2_ri_confidence_scale=80
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.