__  __ 
 |  \/  |
 | \  / |
 | |\/| |
 | |  | |
 |_|  |_|
         
         

   ##    
   ##    
  #####  
   ##    
   ##    
   ## ## 
    ###  
         

     _    
    / \   
   / _ \  
  / ___ \ 
 /_/   \_\
          

 __   __
 \ \ / /
  \ V / 
   > <  
  / . \ 
 /_/ \_\
        
        

         
         
  ###### 
 ##  ##  
 ##  ##  
  #####  
     ##  
    #### 

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen Start]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen%2FQuestions Questions ]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJenseninjector Injector] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenignition Ignition] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensentrigger Triger] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenDisplay Display] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenWbo Wbo2]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenconfig Config] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensentable Table] || *This config is made step by step so it might contain wrong values. Actually, it contains some (most likely bad) values that I have no idea where they could came from *Don: Wbo2 *update 26/10-05 primep=96 # I would use 00 primep_temp_scaling=1A # with primep=00 this does not matter, but 80..A0 is good range cwl=64 # too high, should be appr 25% of cwh cwh=96 cranking_thres=08 # 899 RPM ? kidding ? 02 or 03 should be right (for 299 / 399 RPM) awev=0A # 10% might be a bit low, 15..35% is usually best awev_temp_scaling=33 # very low (would decrease afterstart percentage at high CLT temp), use 9C .. A0 awc=C8 # FF is usually best warmup_clt_range[0]=00 warmup_clt_range[1]=15 warmup_clt_range[2]=28 warmup_clt_range[3]=3C warmup_clt_range[4]=50 warmup_clt_range[5]=64 warmup_clt_range[6]=78 warmup_clt_range[7]=8C warmup_clt_range[8]=AA warmup_clt_range[9]=C8 warmup_clt[0]=C0 warmup_clt[1]=B4 warmup_clt[2]=AB warmup_clt[3]=A8 warmup_clt[4]=A0 warmup_clt[5]=9A warmup_clt[6]=8C warmup_clt[7]=78 warmup_clt[8]=69 warmup_clt[9]=64 warmup_rpm_scale=DD req_fuel=64 divider=02 alternate=10 # 1 injector bank? horrible idea injopen=20 # use 00 battfac=10 # 08 to 10 should be OK kpafac=80 kpaoffs=80 injocfuel=08 # much higher recommended, like 800..1200 usec injrampup_battfac=FF injpwm=38 # PWM duty=22% ( a bit low, but can be OK) injpwmt=1E # PWMing after 3 msec ? injpwm6=20 rpmk[0]=0B # 4 cyl rpmk[1]=B8 tpsdot_kpadot_conf=00 tpsdotrate[0]=0A tpsdotrate[1]=0E tpsdotrate[2]=20 tpsdotrate[3]=66 tpsaq[0]=0A tpsaq[1]=12 tpsaq[2]=32 tpsaq[3]=32 tps_thresh=02 tpsasync=01 acmult=64 tpsacold=28 tpsdq=00 decel_fuelcut_thres=FF overrun_fuelcut=46 overrun_fuelresume=3C rev_limit=46 airden_ignore=62 config11=30 config12=30 config13=02 batt_cal=BC fastidle=D6 baro=64 dbaro=0C tps_low=1D tps_high=B4 fan_temp=55 fan_hyst=09 fan_channel=40 iac_step_seq=01 # IIRC only C9 or D8 makes sense iac_conf=C6 # stepper ? where is the IAC setup documented ? iac_max_steps=FF iac_tps_thres=FF iac_cold_idle_temp=D8 iac_warm_idle_temp=CF iac_cold_rpm=C8 iac_warm_rpm=67 iac_cold_start_pos=E2 iac_warm_start_pos=B0 iac_afterstart_rpm=1F iac_afterstart_duration=20 iac_afterstart_steps=04 iac_kp=25 iac_ki=10 iac_kd=30 iac_integral_speed=C0 iac_integral_limit_dec=05 iac_integral_limit_inc=E0 iac_integral_deadband=0A iac_deadband=05 iac_pid_conf=01 iac_overclose_interval=B8 iac_ref_pos[0]=36 iac_ref_pos[1]=34 iac_ref_pos[2]=33 iac_ref_pos[3]=32 iac_ref_pos[4]=31 iac_ref_pos[5]=30 iac_ref_pos[6]=2F iac_ref_pos[7]=2E iac_ref_pos[8]=2D iac_ref_pos[9]=2C iac_sol_channel=50 iac_ign_advance_change=28 iac_ign_retard_change=20 iac_ign_advance_limit=10 iac_ign_retard_limit=18 iac_ign_threshold=08 ego_conf=06 ego_lag=02 ego_coolant=00 ego_maxtps=FF ego_maxmap=FF ego_minrpm=0A ego_maxrpm=FF ego_warmup=14 ego_lean_limit=0D ego_rich_limit=0D ego_pid_kp=02 mt_unused=00 ego_delta=03 ego_target=19 ego_pid_window=FF wbo2_warmup_ramp=3F wbo2_warmup_target=FF wbo2_abs_limit=E4 wbo2_limit_maxt=A0 wbo2_fallback=60 wbo2_retry_t=01 wbo2_edgetime_corr=BA wbo2_edgetime_min=14 wbo2_ri_target=96 wbo2_nernstdc_target=A6 wbo2_pump_pw_zero=64 wbo2_calibration=A5 wbo2_heater_pid_kp=46 wbo2_heater_pid_ki=10 wbo2_heater_pid_kd=1A wbo2_heater_pid_ilimit=84 wbo2_pump_pid_kp=40 wbo2_pump_pid_ki=2E wbo2_pump_pid_kd=00 wbo2_pump_pid_ilimit=E0 wbo2_ri_confidence_scale=80 knock_conf=01 knock_sampling_window=F2 knock1_frequency=29 knock1_gain=40 knock1_integrator=14 knock2_frequency=29 knock2_gain=40 knock2_integrator=14 knock_threshold=FF knock_noise_scale=D8 knock_max_retard=28 knock_default_retard=04 knock_retard_step=08 knock_retard_delay=FF knock_advance_step=FF knock_advance_delay=50 knock_minrpm=FF knock_maxrpm=05 ve_learn_coolant=C6 ve_learn_max_power=FF ve_learn_rpm_scale=FF ve_learn_kpa_scale=1E ve_learn_ego_scale=43 ve_learn_min_weight=02 ve_learn_speed=FF ve_learn_limit=03 ve_learn_conf=00 lcd_c0=FE lcd_delay=FF lcd_backlight=FF lcd_offs[0]=FF lcd_offs[1]=FF lcd_offs[2]=FF lcd_offs[3]=FF lcd_default_view=00 primary_trigger=01 secondary_trigger=02 tooth_wheel=23 trigger_tooth=01 another_trigger_tooth=12 crank_minper=BC tooth_wheel_twidth1=0A tooth_wheel_twidth2=14 cam_sync_r_edge_phase=FF cam_sync_f_edge_phase=FF reset_engphase_after=D8 ign_tdcdelay=5A ign_dwell14=10 ign_dwell6=25 ign_crank_advance=2E ign_out=70 ignchmax=02 engine_off_delay=08 pump_on_mintime=10 fuelpump_channel=70 inj_stage2_rate=00 inj_stage2_start_tps=00 inj_stage2_start_map=00 als_lowrpm=FF als_maxtps=FF als_ignretard=FF als_rich=FF als_rev_limit=06 misc1out_minrpm=19 misc1out_maxrpm=20 misc1out_mintps=FF misc1out_maxtps=50 misc1out_minmap=FF misc1out_maxmap=FF misc1out_channel=FF misc2out_minrpm=FF misc2out_maxrpm=FF misc2out_mintps=FF misc2out_maxtps=FF misc2out_minmap=FF misc2out_maxmap=FF misc2out_channel=FF act_wot_rpm=26 act_wot_channel=FF act_rpm_rpm=FF act_rpm_channel=48 egt1_cal=00 egt1_offs=00 boost_conf=A0 boost_targetoffs=32 boost_minpressure=32 boost_pid_kp=02 boost_pid_ki=08 boost_pid_kd=07 boost_pid_ilimit=FF boost_channel=60 water_pump_temp=00 hybrid_rpm_a=00 hybrid_rpm_m=00 water_pump_hyst=FF water_pump_channel=8F toothrel_normal=65 toothrel_missing=80 fuelcut_min_kpa=00 fuelcut_max_kpa=FF tach_channel=8F tach_divider=66 '''How was this config made ? Seems like many values are OK, but there are (several!) randomly very bad values here and there'''. Please document the intentions (separately for each subsytems!), otherwise it's impossible to tell that the highly suspicious values are intentional or by error. Maybe this was just used for testing the board ? If so, only wbo2_pump_pw_zero=64 is valueable (egt1_cal obviously not). You should start from someone's working config, and replace sections (a few related values) with other's (also working values), and do your own adjustment as appropriate.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.