_______ ( ____ \ | ( \/ | | | | ____ | | \_ ) | (___) | (_______)
|\ /| ( \ / ) \ (_) / \ / ) ( | | \_/
____ | _ \ | |_) | | _ < | |_) | |____/
__ __ \ \ / / \ \ /\ / / \ \/ \/ / \ /\ / \/ \/
_____ | __ \ | |__) | | ___/ | | |_|
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: Need help to get this “nice” jap trigger working Car Toyota Engine blacktop Cas distributor 4 spots on shaft * tooth width == 180 crankdegrees ? ---- '''Primary trigger input setup''' * input DC voltage measured with input open ? * input DC voltage measured with input pulled to ground with 1kOhm resistor ? * ECU serialnr ? * can you temporarily place a '''magnet on a crankwheel''' and use a HALL sensor as reference, confirm with scope ? ** it's sometimes difficult to make a proper permanent sensor mount but perhaps not very demanding to temporarily mount for verification in the garage ---- '''Ign output setup''' Coils ?? ... ---- Problem: When setting up ignition to 17 degrees BTDC at 1000 RPM, its only 7 degrees at 5-6000 rpm so its sliding almost 10 degrees. '''Measured how ?''' * Seen this problem long time ago but due not remember what caused it. ** '''capacitance on input causes appr 278 usec delay on input ?''' - this can cause the said delay at higher RPM. Can you try the primary trigger falling edge ? Can you scope the input signal ? If this is the case, you can decide to shape input signal properly, or if it's perfectly reproducible, just compensate ** wrong edge of output ? No, that would be too MUCH sparkadvance at higher RPM * tooth width? ** 180 crankdeg, seems good * does validate warn about strange values ? ** apparently nothing relevant * is RPM smooth (or fluctuating) ? * '''MAYBE TIMING LIGHT triggering on wrong edge ?''' ** is it a smart timing light ? * Logiclevel coil ? Maybe the coil firing on the wrong edge ? * maybe the wheel changes position ? ** cambelt sloppyness + mechanical hysteresys ? We scoped on bench, ignition is exactly as shown, no "sliding" at higher RPM. Write (above) about coils, check carefully that * coils fire on the edge when output is deactivated (after dwell), not automatically earlier (eg internal current-limit ??) * that strobelight measures actual spark (not the dwellstart ~ activation of ign output) and that * strobelight does not have some special compensation (it actually lights up exactly at spark, no compensation) * is the input not sharp enough ? Fill in above ---- Triggerlog 1 17 degrees http://www.vems.hu/files/MembersPage/PeterJensen/toyota/v3.3_n004171-2012-09-26-15.53.17_17degrees_.triggerlog Triggerlog 2 27 degrees http://www.vems.hu/files/MembersPage/PeterJensen/toyota/v3.3_n004171-2012-09-26-15.50.09_27_degrees_.triggerlog ---- Log (Config missing) http://www.vems.hu/files/MembersPage/PeterJensen/toyota/ ---- '''Bench Testing Results''' We ''benchtested your setup today''' with 1.2.6 firmware and scope. It '''behave perfectly, we didn't find any "ignition sliding"'''. Ignition seems to fire at good times at any RPMs. For example at 1000,3000 and 5000 RPM (with sparkadv locked to 25 BTDC), ignition angle is ~55 degrees (TDC after the trigger is 80, so 80-25=55) as calculated. http://www.vems.hu/files/MembersPage/PeterJensen/toyota/1.2.6-v3.3_u004521-2012-10-01-13.50.42.triggerlog http://www.vems.hu/files/MembersPage/PeterJensen/toyota/1.2.6-1000-3000-6000RPM.logicdata.zip Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.