##      
 ##      
 ## ##   
 ####    
 ## ##   
 ##  ##  
         

 ###     
  ##     
  ##     
  #####  
  ##  ## 
  ##  ## 
 ######  
         

_________
\__   __/
   ) (   
   | |   
   | |   
   | |   
___) (___
\_______/
         

         
#### ### 
 ##   #  
 ##   #  
  ## #   
  ###    
   ##    
         

         
    ###  
   ##    
  #####  
   ##    
   ##    
   ##    
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
General Questions ---- 30/1-2018 Haw to connect flex fuel sensor to pcb 3.8 ECU 9952 How to connect GenBoard/VerThree/FlexFuel sensor to the "SCL" of v3.8 pcb * note: 2nd wheelspeed available on pin if ECU ordered with 2nd wheelspeed, eg EC10/pin6 below (or is that a separate project ? Please never mix different projects on same page, please create separate page) ** check the paper docs received with the device. ** Safe to feed frequency or other 0-5V signal with 1k to unknown EC10 or other pins (and see wheelspeed [http://www.vems.hu/vt/help/v3/v3_analog_input_calibration.html analog input] reactions in VemsTune) See GenBoard/VerThree/Schematic to connect to port SCL * check in the schematic which AVR pin, and measure if at least the protection resistor is there. [http://www.vemssupport.com/forum/index.php?topic=2499.0 On v3.8 filter and protection is embedded in PCB] * see InputTrigger/WheelSpeed '''Second Wheelspeed input''' and any references, eg. SubaruEj * Note: normally wheel speed 2 is wired to EC36 pin 30 ** this pin also goes to p259 ** no NEED to cut the p259 trace, the p259 output does NOT pull to GND (or do anything) if not activated. ** so wiring SCL to EC36 pin 30 can be done without tracecut. ** only start any such modification if willing to follow the schematic to verify any hint, and avoid static electricity damage http://www.vems.hu/files/MembersPage/PeterJensen/wheelspeed2.jpg http://www.vems.hu/files/MembersPage/PeterJensen/wheelspeed2_back.jpg ---- '''BMW 88 pin Boost valve''' We need to connect a '''N75 boost valve''' to this 88 pin ecu but what pin will we connect to? '''Econoseal 10 pin connector''' Pin 8 and 9 Extra output with flyback. * What does it mean ? (p259 or inj-FET or what ?) ** exactly as written, same as in VemsTune * so in VemsTune, outputs menu select boost control and '''choose''' ** '''Extra output 5''' if you connected to "Extra output 5" ** '''Extra output 6''' if you connected to "Extra output 6" http://www.vems.hu/files/MembersPage/PeterJensen/51731635411_2.jpg ---- Round only AIM Hi Setting up aim coolant temperature something goes wrong while temp goes form 99 to 100 degrees. Should be 100 but at the display i can see number 180. I have used the predefined values and working great until it gets to 100 degrees. Firmware version 0.5.3
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.