__     __
 \ \   / /
  \ \_/ / 
   \   /  
    | |   
    |_|   
          
          

         
         
  ####   
     ##  
  #####  
 ##  ##  
  #####  
         

         
    ###  
   ##    
  #####  
   ##    
   ##    
   ##    
         

      #  
      #  
  ### #  
 #   ##  
 #    #  
 #   ##  
  ### #  
         

         
         
  ####   
     ##  
  #####  
 ##  ##  
  #####  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Consumer Cars Please make the reference to VemsTune and not mcd/mct commands (not all installers know what meaning of the tags ) ---- Volvo 5 cyl turbo 1999 When setting up this car I ran into problems. Firmware is 1.1.75 as requested Crank 60-2 Cam 180 degrees = high next 180 degrees = low the test result is based on bench testing because I think there may be something wrong with the crank trigger wheel, it seams that I louse a negative signal somewhere maybe a ion fragment but I will confirm later. The car cranks at 161 VT rpm´s so I set the signal generator (jimstrim) to 161 rpm. At 161 rpm I get the cync getting on and off. Trig tooth 5 and 60 sensor degrees. If I type 63 degrees it´s working correct. The strengths part is if I set crank/after start switching point to 99 (norm 300) the problem are gone What I seen Trig tooth 5 and 60 sensor degrees crank/after start switching point to 300 rpm. 100-130 = good 131-173 = bad 174 – and up is good Config http://www.vems.hu/files/MembersPage/PeterJensen/volvo_t5/Volvo_5t_1175_marcell.vemscfg Peter ---- Bmw E46 stretch six cyl. New strategy: Only pre_trigger used Firing order 1-5-3-6-2-4 Ignition wiring: cyl. 1-6 to ec 36 pin 24,10 cyl. 5-2 to ec 36 pin 34,36 cyl. 3-4 to ec 36 pin 35,33 So firing this way h2 vemstune 0 ign out 6+7 ec 36 pin 24, 10 1 ign out 2+3 ec 36 pin 34, 36 2 ign out 0+1 ec 36 pin 33, 35 ---- Injector wiring: inj 1 cyl 1 to output 1 pin 7 inj 2 cyl 2 to output 2 pin 19 inj 3 cyl 3 to output 3 pin 8 inj 4 cyl 4 to output 4 pin 20 inj 5 cyl 5 to output 5 pin 9 inj 6 cyl 6 to output 6 pin 18 So inj firing order is: (maybe this have to be moved two places) norm 1-5-3-6-2-4 to 4-1-5-3-6-2 Venstune injgrupe 0 cyl 2 out 2 pin 19 injgrupe 1 cyl 6 out 6 pin 18 injgrupe 2 cyl 3 out 3 pin 8 injgrupe 3 cyl 5 out 5 pin 9 injgrupe 4 cyl 1 out 1 pin 7 injgrupe 5 cyl 4 out 4 pin 20
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.