###      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
######   
         

 _       
( (    /|
|  \  ( |
|   \ | |
| (\ \) |
| | \   |
| )  \  |
|/    )_)
         

  _____  
 |  __ \ 
 | |__) |
 |  _  / 
 | | \ \ 
 |_|  \_\
         
         

______ 
| ___ \
| |_/ /
|  __/ 
| |    
\_|    
       
       

 ___   
(  _`\ 
| ( (_)
| |  _ 
| (_( )
(____/'
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Audi PnP Standart box '''aan/16082''' no spark. Marius Helmersen Norge Audi S4 AAN. Ecu installed but they have * '''no spark while cranking'''. * They have spark in test mode. * They have stable Rpm reading * They have Stable Rpm tachometer * They have injectors firring while cranking. * It is not in safety mode. * Car runs with PnP BOX AAN 3742 (is box 3742 a jumper wire box or new pcb) * Installed same config as the running box 3742 *Is box 3742 different from box 16082? could be that Ign. coils + is low at cranking and only high at ignition on. Log of cranking the car. http://www.vems.hu/files/MembersPage/PeterJensen/S2_log/v3.3_u016082-2018.07.06-22.16.26.vemslog Trigger log http://www.vems.hu/files/MembersPage/PeterJensen/S2_log/v3.3_u016082-2018-07-08-19.26.39.triggerlog Any ides why there is no spark? '''Is there someone who can help Marius Helmersen in Norway or middel of Sweden, dealer, installer, retailer''' ----- Hello Peter/Marius, I have reviewed your vemslog and triggerlog from box 16082 (linked above), from software side i see no reason for spark to be missing during cranking, ecu is scheduling sparks and executing them (according to triggerlog). To get a better understanding of your situtation if have some questions: 1) In review of your coil output configuration it seems you are using active coils (VAG style COP or alike) wired to extra outputs on the breakout loom, does this match your hardware configuration ? 2) Was the spark test mode coil testing performed using box 16082 or box 3742? If you can answer these Q's for me, we'll work from there. Thanks! Best regards, Dave Thank you Dave New info:13/9-2018 They did NOT see all coils firing in test mode but maybe only one. They started to upload a 4 years old config to this new ecu. Mattias Sayed that ign output is changed in the new "PCB" version PnP AAN. Old AAN used 4 x stepper and one ign logic level. And new PCB version use 4 x ign logic level. Can someone uploade a vems.hu oem config AAN pcb version (Dave, Marcell) so I can see what is up and down in this case. Where do I find schematics for this "new" AAN pcb? TNX Peter ----------------------------------------------------------------- * btw the most common reason is: SafetyMode ** VemsTune shows a big fat warning (and red flag) in that case, so usually noticed, but please check anyway. Very easy to upload full config (again) to fix it. ** another hint to check: VT version reasonably uptodate ? +Update ini files from web. * maybe ordered v3/16082 with some special, eg. HALL/HALL input ? The '''correct order of installation/testing''' * is to '''test inputs, independently of outputs: with outputs disconnected''', or disabled (removing fuses is easiest). ** including input-trigger(s), of course''' ---- '''Trigger voltage measurements''' * primtrig-VR (crank 135 pulse) DC voltage ? ** same with both ECU-s ? * sectrig crankhome-VR * cam-HALL DC voltage ? (when lo and when high) '''NEEDED: Config''' will be uploaded later. * Good, because it seems either config is the problem (which can be reviewed when uploaded); ** or trigger input; which can be tested on site. (capture and publish triggerlog, see InputTrigger/TriggerLog ) ** if no triggerlog pulses, '''disconnect the HALL sensor and insert temporary wire between GND and sectrig cam-HALL signal''' (assuming cam-HALL inverter, which is standard). => try again. Car is also tested using box AAN 3742 and the car is running perfect. * not a substitute for config and triggerlog, but useful info. ** note: the HALL of 3B can be outside the crankhome-VR, but not for the AAN. So not very likely in this case, esepecially if runs well. ** note: do the measured input trigger voltages (or better: waveforms) differ with the 2 ECU-s ? * what '''OscilloScope is on-site ?''' (now obligatory). Please make some ESD precautions, and follow install steps (including notes of verifications/measurement). Apparently running into more issues recently (of different kinds, that are difficult to link/relate, perhaps ESD or supply spikes, or some handling could be the common denominator - the probability that it is just luck falls exponentially after every issue ) than 10 other shops combined. ---- '''p259 outputs''' - suspect if VR inputs do not work. * tachout works ? (eg. DC measurement, test mode; or other indication of p259 working well) * anything else on p259 ?
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.