_______ 
(       )
| () () |
| || || |
| |(_)| |
| |   | |
| )   ( |
|/     \|
         

 _     _ 
( )   ( )
`\`\_/'/'
  `\ /'  
   | |   
   (_)   
         
         

         
### ##   
 ### ##  
 ##  ##  
 ##  ##  
 ##  ##  
#### ### 
         

 _       _ 
( )  _  ( )
| | ( ) | |
| | | | | |
| (_/ \_) |
`\___x___/'
           
           

         
|\     /|
| )   ( |
| |   | |
| |   | |
| |   | |
| (___) |
(_______)
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Hi I am starting building the VEMS board for my Corrado g60 turbo. Corrado 1989 1800 ccm Turbo Garret T3 60 trim Mail: motor at webspeed.dk http://www.vems.hu/files/PeterJensen/config/config.txt http://www.vems.hu/files/PeterJensen/tables.txt/tables.txt http://www.vems.hu/files/PeterJensen/imag/cor.jpg http://www.vems.hu/files/PeterJensen/wiring/36-1_diagram_vems.jpg http://www.vems.hu/files/PeterJensen/wiring/36-1_diagram_vems.cdr *Make your wiring with Corel Draw just download the “cdr” file all images are already made ---- '''Need help for Wbo2''' When I issued the command &#8220;Manmde02&#8221;, the heater turned ON but it seemed to turn OFF again after one scan. The problem was: 1A supply was too weak If the supply is too weak: * GenBoard might reset. The uptime seconds counter (that is seen eg. in MegaTune) resetting to 0 shows this * or possibly, if the sensor is not heated in a reasonable amount of time, the heating decays to wbo2_fallback for wbo2_retry_t time when the heater PID controls takes another chance. La:??.? should be displayed when the heater does not reach target. If you want to tweak the settings, check the following config variables: (copied from global.h, the firsthand source of variables) <code> uint8_t wbo2_limit_maxt; // wbo2, max time spent at abs_limit [262msec] uint8_t wbo2_fallback; // wbo2, fallback V after maxt [1c=10V ff=30V] ... actually this comment is bogus, FF is 100% uint8_t wbo2_retry_t; // wbo2, retry control after [4sec] </code> ---- '''Need help for compiling firmware''' The released binary from GenBoard/UnderDevelopment/FirmwareChanges has WBO2 enabled. (in my_make MY_CONF += -D WBO2) I triad to compile like: 1. Make clean 2. sh 3. make all But no vems.hex fil will be generated http://www.au2stereo.dk/compiler.jpg http://www.au2stereo.dk/compiler1.jpg If you insist on compiling: * provide link to zip of some of your files, eg. ** my_make ** winavr version ** output of avr-gcc -v ** error messages: preferrably not images, but text files using output redirection or copy-paste (click on upper-left corner, edit menu)
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.