_______ ( ___ ) | ( ) | | (___) | | ___ | | ( ) | | ) ( | |/ \|
_____ | _ | | | | | | | | | \ \_/ / \___/
|\ /| | ) ( | | (___) | | ___ | | ( ) | | ) ( | |/ \|
## ## ###### ###### ## ## ## ##
##### ## ## ## ## ## ## ## ##
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: ''' Corrado g60 turbo ''' || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen Start]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen%2FQuestions Questions ]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJenseninjector Injector] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenignition Ignition] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensentrigger Triger] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenDisplay Display] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenWbo Wbo2]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenconfig Config] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensentable Table] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenwiring Wiring] ||[http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenidle Idle]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenTools Tools] || ''' VW Passat ''' || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenPassat Start]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenPassatThrottel Elektronic throttel]|| ''' Audi S2 ''' || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenAudiS Start]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen/AudiSQuestions Questions ]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen/AudiSinjector Injector] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen/AudiSignition Ignition] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen/AudiStrigger Triger] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen/AudiSDisplay Display] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen/AudiSWbo Wbo2]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen/AudiSconfig Config] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen/AudiStable Table] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen/AudiSwiring Wiring] ||[http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensen/AudiSidle Idle]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenTools Tools] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FPeterJensenConsumerCars ConsumerCars] || ConsumerCars ---- 2010-03-04 (please don't mix with data from '''any''' other projects. This is important ! Cannot get a good overview that wastes a lot of time and makes it hard to help). Split this project to a page of it's own (or move the info that relates to other projects). Need support to get the sec_trig HALL working * primary_trigger=05 ** this seems totally bad, invalid config. Not sure where they got it from. Why not starting from a working 60-2 setup ? For missing tooth setup, turn off filtering (advanced filtering is an option, but it should NOT be needed either) * secondary_trigger=18 * tooth_wheel=3A * h[1]=64 50 3C 28 14 00 FF FF ** this is OK for 6 cyl when sectrig enabled. ** but h[1]=00 64 50 3C 28 14 FF FF provides faster startup during cranking (rotate the ignoutputs to match). ** Need to change to h[1]=00 28 14 00 28 14 FF FF when disabling sectrig (eg. when trying with wasted spark ignition. or just testing primtrig sensor, RPM, etc...) Car '''Bmw E46 6 cyl COP''' pri_trigger 60-2 hall is working. sec_trig hall * some BMW have VR cam sensor. Detail how you got certain that this engine has HALL. Sensor Ohm measurements ? Due anyone know ware to find the schematic on 3,6 . having trouble to get the sec_trigger hall to work? **Thanks Marcell Her is the correct pic of the board taken of the exact board (by reseller) * he installed the 0 Ohm correctly. So the EC36/13 cam-HALL signal should now get to the processor (w/out camHALL inverter. good). unfortunately they have made the measurement wrong, '''they could not measure 5 V at sec_trig with disconnected sensor''' * maybe a broken multimeter * maybe bad ground wiring blew up p259 chip inside shorting the small 78L05 SOT89 regulator's output to ground ? ** This voltage measurement is absolutely very important. We MUST know voltage measured without sensor. MUST be >3V, '''otherwise there is absolutely no way the sectrig HALL could work !!! ''' ** Should preferrably also measure the voltage when pulling with 1k (or similar, but known resistance) towards ground. (That would confirm the internal 2k7 pullup resistance toward +5V => eg. that it's not shorted or something...). With the sensors connected they have no rpm at all * and if disconnecting sec_trig (Vt) they have fine rpm. ** rephrase this sentence. You mean "disabling" sectrig (in config) ? So please see the config if something is wrong and also validate the hardware. Tnx Peter http://www.vems.dk/Bmw_1167.vemscfg http://www.vems.dk/Bmw_sec_trig.jpg ---- * the 2k7 EC36/13 input pullup is there, good * the other 2k7 is OK (any value from 0-10k would be OK, since you don't use cam-HALL inverter) * '''you seem to miss the "B=>C" blob''' from the sot23 transistor pads. Just solder a blob there, or a very small value resistor, like 18 Ohm (leave the 3d "gnd - emitter" pad alone.) ** apparently that's all you need to get the signal to the processor. The '''cathode of the 5V1 (SOD80 smd) zener goes directly to the processor pin'''. http://www.vems.dk/sec_trigger.jpg The board is ordered with sec_trigger hall but i think there is missing something see pic. Can I make a wire her to make it work http://www.vems.dk/sec_trigger_1.jpg ---- 30/3-2008 After several attempts I got the main.hex uploaded to Avr but I have not been abele to get the serial communication working what could be wrong? I have tried command S,s Man but no serial contact Avrdude version: avrdude-5.6cvs.tar http://www.vems.hu/files/MembersPage/PeterJensen/avrdude_1.jpg '''Bootloader ISP upload''' '''To upload main.hex using Avrdude and ISP''' find main.hex in http://www.vems.hu/download/v3/bootloader/ http://www.vems.hu/files/MembersPage/PeterJensen/avidude.jpg ---- ''' I have a problem with contacting megatune''' Vems have been subjected to great hardship as there has '''been a bad ground connection'''. * p259 is usually the first victim (often the LM1815 VR trigger chip supply gets lost), but the fetdriver, mcp3208, i259, the processor or other chips can get damaged. when I turn on Vems can I get connection for about 2 seckunder with megatune and then lose my connection. * just in case, check firmware version (ManmdV and megatune version). after 2 seconds prosessoren bring some of the output high * high or active ? Active means low for injector control pins (because fetdriver is inverting) * which legs ? Is it possible to delete the program in prosessoren and then upload a new firmware ? * yes, just upload a firmware. ** you can verify before uploading new firmware, to see if it changed since you uploaded (this is extremely unlikely though) ** if you cannot upload via megaloader / vems.hu/download/v3gui/ vemstune, and suspect bootloader damage, it is possible to remove endplate and reupload bootloader with ISP, but this is extremely unlikely to be the solution (damaged bootloader is just very unlikely ). ---- '''Dual Stage Injection''' A friend of mine is consider to buy Vems and he has some questions: Can Vems run dual stage on a 5 cyl. S2 engine (10 injectors) If yes can he adjust the petrol/methanol (second stage) like a look up table? He likes to have petrol like normal 5 1025 ml. inj. And petrol mixed with 20% methanol fore the five-second stage injectors and it is necessary to could adjust the mix in rpm and load you can set the flowrate ratio of injectors (first and 2nd stage). You don't need to set 2 VE tables, just one. The 2nd stage is only used at higher pulsewidth (higher load). ---- '''Audi S2 standard TEMPERATURE sensors''' Need to calibrate the mat and coolant. What airXfactor hex and cltfactor hex. See * EasyTherm ** EasyTherm/SensorTable * MembersPage/MarcellGal/PowerAndTraction/TempTables The best for coolant is 1900 256 (shows appr 10C lower, so you get indication well above 102C coolant temp). For air: 425_260 is a good starting point for a PTC, with the 430 Ohm pullup (2700 Ohm x 510 Ohm). Minor note: even if you have an NTC table in the ECU right now, the reading is useful to find out where the ADC is at certain temp to make a good choice: download calibration zip from EasyTherm and use the csv spreadsheets). ---- Question: Is this a good setup fore 60-2 trigger. Peugeot 2,0 Please comment: '''Next trigger tooth must be 30 !''' Also, strobe the engine for exact ign_tdcdelay (1 tooth + 60 degree might not be dead on). http://www.vems.hu/files/MembersPage/PeterJensen/trigger.jpg Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.