____  
 |  _ \ 
 | | | |
 | |_| |
 |____/ 
        

         
 ######  
## ## ## 
## ## ## 
## ## ## 
## ## ## 
## ## ## 
         

         
         
 ##  ##  
  ####   
   ##    
  ####   
 ##  ##  
         

 ___   
|  _`\ 
| (_) )
| ,  / 
| |\ \ 
(_) (_)
       
       

  ______ 
 |  ____|
 | |__   
 |  __|  
 | |____ 
 |______|
         
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Porsche 944 turbo Ordered following items: Products ------------------------------------------------------ 1 x MAT sensor () = 23.97EUR 1 x Sealed sensor connector () = 35.70EUR pincount 10-Pack Sex pair 1 x Bosch motorsport ignition (Bosch) = 127.00EUR ignition driver 2 3 x Pneumatic tube () = 23.94EUR temperature 180C 1 x K-thermocouple connector (K) = 12.70EUR Sex pair mounting-style flying loom 1 x Econoseal18-Wire () = 8.00EUR 1 x EconoSeal36-Wire () = 9.00EUR 1 x Econoseal / JPT Crimptool () = 39.90EUR 1 x Assembled v3.3 controller (v3.3) = 602.16EUR secondary_trigger auditrigger primary_trigger VR PowerFlyback yes mounting-style screws MAP connection 300kPa onboard (6/4mm pneumatic) LCD and PS2 yes Knock and EGT yes 1-wire interface no ignition driver 4 1 x EGT sensor (K-type) (2x90mm) = 59.70EUR 3 x K-compensational cable () = 1.11EUR I thought to use partly old wires, most grounds will be new. Questions: Original TPS Bosch 0280120400, 5 pin connector. Can it be used? Original IAC BOSCH 0280 140501 3 pin connector, ok? Original CLT Bosch 0280 130026 ok? Best place to set IAT, before or after TPS? *Note that VEMS can be configured as "auditrigger" sec. trigger setup and accept Porsche 944 Turbo stock starter gear ring+crank home trigger arrangement. A bit more work perhaps, but install will be neat and clean (i.e. no additional trigger wheel etc). MembersPage/PeepPaadam Has anybody really got VEMS workin with Porsche original trigger, wich are 130 tooth flywheel (vr sensor) and 1 reference tooth on flywheel (vr sensor)? Porscche turbo has 132 tooth flywheel and one ref sensor 58.28 dec BTDC A '''V3.3 ordered for Porsche original trigger (auditrigger) can use''' * primary trigger VR (which can be either crank or cam) with sectrig disabled * or primary trigger=VR and secondary=VR ** but primary trigger=VR and secondary=HALL requires removing a small solderblob at the bottom of the board slightly under the FETs (in good light conditions possible with just endplate removed) '''A:''' MembersPage/MagnusKarlstrom has his 944 working on original 130teeth+crank home signal. You have to order VEMS as secondary trigger auditrigger option. Question: about plug and play motronic. Wonder does the shielding of vr sensors work if i use some kind of daughterboard to install VEMS to motronic connector? Any experience? * apparently most people solders wire between the VEMS genboard (mainboard) and the motronic connector (a bit hack, but it works, and some hotmelt secures it mechanically).
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.