#####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
         

 _______ 
/ ___   )
\/   )  |
    /   )
   /   / 
  /   /  
 /   (_/\
(_______/
         

  _   _ 
 | | | |
 | |_| |
 |  _  |
 |_| |_|
        

     ### 
  #####  
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  ### ## 
         

__   __
\ \ / /
 \ V / 
 /   \ 
/ /^\ \
\/   \/
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Porsche 944''' turbo/Injector & Flyback ? (v3.x serialnr 731) Due to engine failure, I had to build a new one. Found 3.0 litre 16valve Porsche 968 engine as a starting point. Now with Carillo rods, original forged pistons, cometic 3,2 mm headgasket, wich brings C/R down to 9,5. Garrett GT35/82R turbo. Engine harness has been built out of original 968 wire harness, each injector have own wire. Bosch wasted spark coil pack from VEMS shop. Racetronix high Z '''846cc/min''' injectors. Does the harness happen to have some transient diode in EC36/23 flyback connection ? * if yes, please bypass (short) that transient diode ** injector+ should be direct to EC36/23 ** changed v3/731 to 30V flyback (2019-09), injector closing faster and more reproducible (with lower voltage, injectors close slightly sloppily, and not all 4 with the same speed) ** idle will be smoother (injector pulsewidth will be slightly longer) ---- '''Trigger''' : See MembersPage/PeteLeh/PorscheTrigger (132+1) ---- VEMS: serianr: v3/731 VR/Auditrigger without cam-HALL inverter '''Changed v3/731 to 30V flyback (2019-09)'''. Originally Power flyback. 300kpa MAP LCD&PS2 4ign Driver * 2006-2009: Firmware 1.1.47 ** first: Fuel pressure ok, I get some burning, in combustion chambers, but the engine did not start. Was configured and tuned later, and used for years. ** later firmware upgraded to 1.2.31 (might upgrade to 1.2.38 in 2019), have yet to be tuned. --------------------------- Wiring has been done by using Porsche 968 engine wire harness, wich is connected to porsche 944 Turbo Engine bay and cabin connectors (very straight forward). Motronic 55 pin connector has been cut away and wires connected to EC 36 and EC 18 connectors. Few extra wires had to put. ( When I ordered VEMS the plans were others, so I did not order it with 55 pin Motronic connector) Here is schematic of EC connectors with corresponding DME PIN.s EC 36/ Wire colour/ Object/ DME pin/ Other 1 Gn/Re TPS signal 26 DME Maf sens wir 2 Gr/Bl IAT 33 Tank ventvalv Wi 3 4 5 GND 6 Bk/Wt ICV close 22 Flyback Diod 7 Gr/Bk Inj.1 17 8 Gr Inj.3 35 9 Boost ctrl Flyback Diod 10 Re/Bl Gn/Bl Tacho 6 22Ohm+220uH 11 12 13 14 Ye Clt sensor 47 15 '''Fuel pump relay- : Please use injector output (injout-E as originally)''' 16 17 Re/Bl ICV open 4 Flyback Diod 18 Bl/Re Variocam 23 Flyback Diod 19 Gn/Re Inj.2 16 20 Gr/Bl Inj.4 35 21 GND 22 23 24 GND 25 Re/Gn Re/Ye Power 37 Fuse Box 26 GND 27 Br Speed sens 27 Pin 1 Connector 28 29 Ye/Re TPS +5V(1) 25 DME Maf sensor wire 30 31 32 33 34 Br/Ye Coil Pack1 New wire 35 36 Ye Coil Pack 2 New wire EC18/ Wire colour/ Object/ DME pin/ Other 1 Wt Knoc sens 1 11 2 Shield Knock sens 3 Wt knock sens2 29 4 5 6 7 Br WBO2/5 8 9 Gn/Re WBO2/6 10 11 12 Br Ref sens DME 26 Pin 1 connector 13 Bl/Gr WBO2/1 14 DSUB3 15 DSUB2 16 17 18 Ye/Re WBO2/4 Update: I got Porsche running and tuned using anvient1.1.44 firmware and megatune. Dynoed up to 400hp with moderate boost, manual boost control. Car had boostcreep and wastegate was chewnged to synapse 60, manually controlled. Then got some kids etc family stuff, so car was left standing for years. Now I have some time for hobby again and started to get car running again. I was not completely satisfied with engine wireloom: too many wireconnections, allthough there were no issues with them. So I built a new wireloom using an other old Porsche 968 engine wireloom as base. All connections are as abowe, difference is with power wires, wich are as Porsche 968 has: Injectors IAC and variocam solenoid share same wire and fuse, as is in original Porsche. They all also are connected to flyback wire. No separate flybackdiodes in loom. ECU has own fused power source, so has ignition. Boost control not connected. I triued to start the engine with old firmware and megatune, but had one groundwire wrong, so burned p259 chip. ECU was sent to VEMSSHOP for repair, and got exellent and fast service. Groundwires were corrected, also all wires checked many times. Got ECU back, and '''firmware was updated to 1.2.23'''. * Can you check this ? 1.2.23 is weird, 1.2.38 or 1.2.43 recommended Checked Firmware: was 1.2.31. will update to 1.2.43 * So I started to configure with VEMSTUNE and tried to start the engine. ** See VemsTuneVersion First I got decent RPM reading, both tachometer and VEMSTUNE. Injectors were not connected yet. Also fuel pump was priming and got fuelpressure up. After few runs I lost rpminformation. I connected the fuelpump to EC15/36 to see if p259 chip is working, and fuel pump did not prime. So I thought the chip is burned again and ECU was sent for repair/upgrade * it turned out that ECU is ok, to be specific: the '''"sectrig"="use as primary" setting was configured''' (most likely accidentally and unknowingly) ** but primtrig was connected to EC36/27 as normally (not to sectrig input) which obviously resulted in 0 RPM reading (and empty InputTrigger/TriggerLog ) ** note: Always [https://shop.vems.hu/catalog/refer_to_thematical_page.php report digitally], and request review before sending ECU * Now checking the wires and sensors again. ---- '''Upgrade 1.1.44 => 1.2.x''' * Also continue configuration as there are lots of changes between 1.1.44 and 1.2.23 ** With newest VemsTune, after "update ini files from web" (see VemsTuneVersion ) after uploading 1.2.38 fw, and ** (using the new, updated VT) '''upload old (1.1.44 is really old)''' config to the ECU ('''File / upload config ; select .vemscfg file'''), most new variables get filled to default values ** "validate" is needed, and some manual intervention is needed, this is most likely an easier path than
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.