##  ##  
 ##  ##  
 ##  ##  
  ####   
   ##    
         

  _   _ 
 | | | |
 | |_| |
 |  _  |
 |_| |_|
        

 _____ 
(  _  )
| (_) |
|  _  |
| | | |
(_) (_)
       
       

         
         
  ###    
     #   
  ####   
 #   #   
  ### #  
         

         
  #### # 
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
     ### 

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Car is my friends '86 928 S with 4.7litre V8, Strosek body kit and ultra-wide Folger 18inch wheels. Engine produces 310hp stock. This is the beast: http://www.carrating.org/documents/cars/u/U3R3o585q6Z5p5o1x252.jpg Car is running very well right now. -------- It had LH-Jetronic from the factory. LH was fuel only, spark was distributed by two(!) 4cylinder dizzys! I threw old engine compartment wiring off and applied 8 VW COP ignition coil. Car has 100-1 tooth wheel on the flywheel with VR sensor. '''Redline RPM''': 7000rpm '''10000 RPM possible with 100-1 trigger wheel''' * separate page for ignition: MembersPage/PeepPaadam/PorscheIgnition * VR sensor; after some tweaking I got '''steady rpm signal without trigger errors'''. (On cranking and low rpms, there are no wheel errors). ---- '''COPS''' * VAG part number 036 905 715 A ** It turned out that the owner gave me wrong pinouts for the COPs (this prevented operation for a while); when I found out about it and fixed it by swapping two pins, I got good spark immediately at the plug! I measured the resistance between pins. it's like that: Between pin 1 and 4 = 390 ohms, between pin 3 and both 1 and 4 40kOhm and betweens pins 3 and 2 16kOhms. Correct pinout is like this: pin1 & 2 - '''GND''', pin3- '''+12V supply''', pin4- '''Signal''' ---- 26.09.06 - old speculation (the COPs were connected according to bad pinout => no spark Got the wiring done and since I have two of the 8 COPs needed, i thought I'd try to get a spark on the plug. Ok, got everything hooked up correctly and I set dwell to 3ms, cranked and.....Nothing! Disconnected the coil and measured (how? what equipment ? what settings ?) the output of Genboard while cranking, it was something like 1.2-1.3 volts for a second and then dropped to 0.08-0.1 volts. If you measure with a DVM in DC mode, that measures '''mean voltage'''. Eg. 5V, 20% of the time (80% off) measures 1V. Yes, I measured DC voltage, appr 1V, so it's all ok then. * Check InputTrigger/TriggerLog ... maybe no need if no wheel errors and RPM steady * MegaTune log is often useful * config and tables for this car: MembersPage/PeepPaadam/Config_Tables ** config looks like wasted spark setup. I'd start the car with wasted spark coilpack, and only move to COP later. * check if the right outputs are selected * make sure there is fuse protection for each ignition transformer (3A per transformer; if it's only possible to fuse them paired, than 5A; use 7.5A if fuse powers 4 channels; use 10A if fuse powers 8 channels, but use more fuses if possible, that is always possible with COPs). * use mdn03 (mdn02, mdn01, mdn00) to fire small spark (make some sparkgap - not necesserily from sparkplug - outside the engine so you can see; make sure the total gap is sufficient, eg. end of stripped wire 1mm from block ).
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.