##  ##  
 ##  ##  
 ##  ##  
  #####  
    ##   
 ####    

         
         
  ####   
 ##      
 ##      
 ##      
  ####   
         

         
         
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
         

   #     
   #     
 #####   
   #     
   #     
   #  #  
    ##   
         

 __     __
 \ \   / /
  \ \_/ / 
   \   /  
    | |   
    |_|   
          
          

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Customer has a drift car, BMW with installed Dodge Viper 8.3liter V10 engine. Engine is odd-fire V-10 (90-54 degrees) * firing order 1,10,9,4,3,6,5,8,7,2 * odd fire TDC 0,54,144,198,288,342,432,486,576,630 * '''WHEN is the TDC following/relative to the sectrig?''' ** it matters little which cyl it belongs to (but take note if you know) '''TODO:''' * considering that internal sync-points are the pulses after the short (18 deg) gap * determine per cylinder ignition delay: alternating 0,18 ?? ** and the 8 entries of reftooth * similar to Maserati config (subaru6+7) but 10 tooth configured: config.tooth_wheel=0a * apparently 5 channel ignition (ignchmax=04) must be configured ** but in firmware the last 2 entries of reftooth, per-cyl delay can be wired in (traditionally "only" 8 channels configurable freely) * check spark at initial sync -------------- '''Primary trigger''' is HALL and trigger type is apparently coil-type (flywheel has 5 pairs of teeth, see photo). https://www.viperpartsofamerica.com/images/products/843_large_image.jpg EDIT: Trigger log: both primary and secondary trigger: http://www.porsche-foorum.org/album/displayimage.php?album=lastup&cat=0&pos=0 * [http://cell.dyndns.ws/del/viper/ same content in zip] * The 72 deg (10 cyl) seem to be 18+54 (18 deg=15.5 / 61.6 msec * 72 deg) * and 18 deg + sectrig comes after 24 crankdeg + following primtrig after 30 http://vems.hu/files/MembersPage/Peep/Viper10cylOddfire/Viper10cyl_oddfire_trigger_18_54__18_S24_30.jpg VEMS reads RPM but throws trigger errors * with what .vemscfg exactly ? Or better .vemslog ? * The config is definitely not good, the spark time is not consistent. Is it possible somehow to mask the 2nd tooth of each pair so that VEMS trats the primary trigger as coil type with 5 teeth? * search for oddfire or Maserati (fphil) ** eg. MembersPage/FPhil/CoilTypeOddFireConfig ------------- '''Secondary trigger''' is HALL, pattern is unknown at the moment. UPDATE: cam trigger is "half-moon" style: one teeth which is 180 degrees wide. ------------- '''Ignition system''' is wasted spark, 5 outputs is needed http://i.ebayimg.com/11/!B0)(jzw!Wk~$(KGrHqZ,!hYEw5P05ggIBMbvI+QelQ~~_35.JPG
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.