##  ##  
 ####### 
 ## # ## 
 ##   ## 
 ##   ## 
         

   ____  
  / __ \ 
 | |  | |
 | |  | |
 | |__| |
  \___\_\
         
         

         
         
  ####   
     ##  
  #####  
 ##  ##  
  #####  
         

         
         
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
     ##  
 #####   

###      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
######   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
See BMWS54B32 related VehicleFitment/BMW/SFiftyFour Project is customers race car, BMW E92 with '''S54B32 engine, straight 6 cyl'''. Factory harness, plug and play adapter and S54 VEMS ordered from webshop with double-vanos and ETC support. Problem is oscillating throttle when TPS is connected, when disconnected oscillation stops (TPS shows ~60%) and obviously motor opens throttle only when pedal is pushed past 60% and then it opens to full. All the connections have been verified (polarity of TPS/PPS GND and 5v), analogue input pins etc. Should TPS2 (on the throttle motor) show ~4.8volts when throttle is closed? Here's current config file (please review ETC part and VANOS part): http://www.vems.hu/files/PeepPaadam/BMW_S54B32_pnp.vemscfg And here's video of the issue: https://www.youtube.com/watch?v=487Q0X98_5I Please could you take a look at this as the 1000 km endurance race is already after a month and we really need to do some testing too.. Thank you in advance! ---- I have working config for that engine, contact me to my email damir.muha@gmail.com Tnx I sent an email. The config I used was in fact from working car (not mine though) (Peep Päädam) ----- Hello Peep, A lot of changes have been applied to ETC code to make it easier to tune since 1.2.23 (see: http://www.vems.hu/wiki/index.php?page=GenBoard%2FUnderDevelopment%2FFirmwareChanges) for proper (and easy control) it is imperative you upgrade to 1.2.31 or later. If after this you still have tuning problems, please upload a vemslog (or create sharing) of ETC operation doing a few slow pps 0-100% sweeps and link it here i'll review and provide hints. Best regards, Vems Dave ---------- I uploaded 1.2.32, calibrated PPS/TPS/1/2 and inserted recommended PID values from help file. Throttle behaves normally now, but only issue is that it does not open fully. Pedal is pressed to 100%, but TPS and TPS2 show 98% and I see that throttles are not fully open. Also is there any way to verify VANOS solenoid operation? I mean to verify that outputs are in fact correct (which output and polarity, e.g. i4/5 or 4/i5). Here are config and log files: http://www.vems.hu/files/PeepPaadam/BMW_S54B32_1.2.32.vemscfg http://www.vems.hu/files/PeepPaadam/v3.3_u010280-2015.06.11-14.56.08.vemslog
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.