## ## ## ## ## ## #### ##
# # # # # # # # ##
_ _ ( ) ( ) | `\| | | , ` | | |`\ | (_) (_)
##### ## ## ## ## ##### ## #####
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: My name is Paal, working and playing with toy cars in Bergen, Norway. Time to update progress in 2009.... ---- '''The goal''' Apply a GenBoard/VerThree (V3.3) to my Polizei-golf's new engine. '''The car:''' http://jeje.je/creative/polizei/polizei.jpg '''The engine:''' *16v KR engine with S2 pistons *S2 intake manifold with S2 TB throttlebody [http://www.s2central.net/images/3B_ECU_Schematic.jpg TPS schematic] *K24 turbo *440cc (high impedance) injectors and 3,5 bar FPR *034EFI idle stepper motor [http://www.034motorsport.com/product_info.php?products_id=161 link] *034EFI wasted spark coil [http://www.034motorsport.com/product_info.php?products_id=40 link] *034EFI IAT sensor [http://www.034motorsport.com/product_info.php?products_id=117 link] *OEM "blue" water temp sensor *Walbro fuel pump (original G60 fuel pump not sufficient) ---- '''VAG 60-2 (BOSCH) Hall trigger:''' [http://i43.tinypic.com/nwmott.jpg Trigger wheel fitted to my crank, illustration overlayed showing 85 degrees between missing tooth and sensor] German thread: http://www.golf1.info/forum/thread.php?threadid=14109&page=2#post151865 and [http://jeje.je/creative/polizei/vems/elsawin-polo-axu-hallsensor.jpg ELSAWIN screenshot here stating it is a Hall sensor, (ro/gn) goes to G40 pin#1 (which we know is Hall), and EGR-potentiometer pin#2 (reference voltage) (TeroK)]) - 85° BTDC with cyl1 at TDC [http://i43.tinypic.com/2rf8zyc.jpg reference] - OEM parts numbers: * sealing flange with 60-2 trigger wheel and plastic clip to align wheel with housing: 030103171L (~65 EUR) * Hall sensor with ~15 cm wire: 030906433Q (~40 EUR) * Steel backing plate: 030103647E (~20 EUR) - some modifications, see vortex thread. * [http://forums.vwvortex.com/zerothread?id=3516017&page=4 Vwvortex thread part numbers for hall sensor connector, wires and rubber grommets] '''trigger settings example from emil (2007):''' * Falling, Multitooth * with trigger tooth 3 * TDC After the trigger = 62 degrees ** is this measured or speculation ? verified via strobing ? ** it's easy to get into the ballpark (+-6 crankdeg) with InputTrigger/TriggerLog, but it's really a good idea to verify via strobing anyway ---- '''VEMS specifications''' Hardware: GenBoard/VerThree V3.3 Assembled v3.3 controller * Options to be decided this week. Todo: * Figure out how to get TACH signal (MembersPage/SteinOvePrestmo did this?) * Control boost with what? Suitable part from webshop? -- '''Progress 2009''' * Engine is in car * Pipeworks, welding intake / downpipe is soon done * Ordering VEMS unit + sensors + harness this week Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.