_____ 
|_   _|
  | |  
  | |  
 _| |_ 
 \___/ 
       
       

         
         
 # ###   
 ##   #  
 ##   #  
 # ###   
 #       
 #       

______ 
|  ___|
| |_   
|  _|  
| |    
\_|    
       
       

         
         
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
    ##   
 ####    

 _       
( (    /|
|  \  ( |
|   \ | |
| (\ \) |
| | \   |
| )  \  |
|/    )_)
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''1981 Volvo 242 DL''' http://oeb.xerc.biz/vems/DSC00020.jpg ---- The car is put together with mainly fabric new parts my dad had lying around in his workshop from his days tuning old Volvo's. * B21ET Turbo engine w/Mitsubishi TD04HL16-T turbo. * Volvo 940 Turbo intake manifold with Bosch 337 cc/min Low-Z injectors and Volvo 850 TPS. * Custom made triggerwheel with Honeywell 1GT101 same as [http://www.vems.hu/wiki/index.php?page=MembersPage%2FMattiasSandgren%2FVolvoBtwenty this car] * Singe coil and distributor ignition, no cam sensor. * VEMS v3.3 firmware 1.0.38. http://oeb.xerc.biz/vems/DSC00258.jpg Trigger hits approx 65-70° after 0°. '''Trigger should give signal ~60 degrees _before_ tdc''' /Emil ---- '''Update 2006-11-17''' The car runs well with standalone ignition unit (Lumenition). '''When using VEMS ignition, I cant get the ignition over 0° while cranking.''' * If I set "TDC after the trigger" lower than "2" my timinglight stops blinking. I tried 5-10-15 and 20 on "Priming, Cranking, Afterstart" - "Cranking advance" and still I get 0° on the timinglight. ** that is no surprise: ** '''"TDC after trigger"''' (ign_tdcdelay) '''should be around 60 degrees''' in this case. Below 40 degrees is invalid setting anyway (It must be 5..10 degree higher than maximum ignadv.) '''Could this be firmware related? (1.0.38)''' MSQ file [http://oeb.xerc.biz/vems/megasquirt200611162228.msq here] '''A:''' TDC after the trigger should be 65-70 if the trigger is mounted properly. if you have it at 65-70 after the trigger, your setting should be 110-115 degrees. Also make sure that ignition offset, under Extras , Advanced ALS is set to 0 degrees. A setting of 2degrees TDC after the trigger will make it impossible to have advance above 2 degrees. '''Q:''' Changing it to 110 and so on didn't quite do it.. when strobing I got about 40-45° and increasing tdc after trigger more didn't help either. http://oeb.xerc.biz/vems/DSC00262.jpg The 1GT101 hits the 60° BTDC tap I marked on the picture. What am I doing wrong? Yes, ALS advance is 0.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.