_____ 
(  _  )
| ( ) |
| | | |
| (('\|
(___\_)
       
       

 ___   
(  _`\ 
| (_(_)
|  _)  
| |    
(_)    
       
       

    ###  
     ##  
     ##  
  #####  
 ##  ##  
 ##  ##  
  ###### 
         

 _______ 
(  ____ \
| (    \/
| |      
| | ____ 
| | \_  )
| (___) |
(_______)
         

 _______ 
(  ____ \
| (    \/
| (__    
|  __)   
| (      
| )      
|/       
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Current setup 2014''': I used Emanage for a while but now I swiched back to VEMS 3.7. '''Volvo S70R''' built '01 B5244T3 LPT engine with ported RN *head, Dual VVT, but my exhaust side is fixed. *2435cc 9.0 compression *TD05/06 HRC 20G turbo *3" free flowing exhaust *FMIC *550 Bosch injectors/ 850cc Bosch EV14 for ethanol *Walbro 255 pump http://i238.photobucket.com/albums/ff56/Nitrox5/VS/10380068_456692697799835_2158828506021511746_o_zps73d4d84c.jpg --------------------------------------------------------------- *Wideband (any LSU4 sensor works) *EGT (after turbo, in dp…should be relocated into the collector) *Volvo COPs..dwell: ~2.1ms@14V (not sure if it’s the right value *for Volvo coil) *'''Trigger setup:''' **h[0]=08 02 01 04 10 20 40 80 /injetor fire order **h[1]=00 60 48 30 18 FF FF FF /Trigger tooth **h[2]=00 70 60 30 10 10 60 60 /Ign fire order *Boost control: done, works with stock TCV *IDLE: stock, works *Tachometer: Can be Motronic or a pulled 12V output from vems (divider 20) *'''Coolant temp:''' ECC also requires it, so we have two options. #*Hook up Motronic, give pos, negative wires and only the coolant signals, but in this case you need a separate sensor for Vems, I used a RN one. #*Create a small 2$ circuit to generate frequency to instrument panel: 40Hz-21Hz (20°-100°) *WheelSpeed/roadspeed: not ready (VEMS boards after 2010 can handle 0-12v signals!) *Knock control: not ready yet (works at my buddy) *Traction control could be set up, but not so important to me. *'''Climate control:''' produce 5°C/ 41°K cold air, works with most of the (important) functions. I had to hook up Motronic to achieve this. IDLE still drops a bit, but I can install a little valve which separately allows more air into Intake when M4.4 activate the compressor. (What missing is compressor disengage control when WOT or high LOAD. I can live without that.) ​ Full automatic, monitors high pressure side, which triggers the fan low/ high speed depending on the pressure. Shut down the compressor over 125°C or above 30bar on pressure side... So it unable to overload. Requires the following signals: Power and grounds, "High" Pressure sensor, stock coolant signal, Pressostat "low" press switch, RPM signal, Low and High speed of the Fan '''Future plans:''' Fine tune start up time, shorter cranking from 2-3 seconds) VVT control setup EVAP control Trip Computer: could be handled in the future, but not important, because Vems can display consumption in main screen, present and average also. ------------------------------------------------------------------------------------------------------------------------------- --------------------------------------------------------------- '''Former car setup on vems in 2010: Volvo 740''' 1st setup was: B230FT, ported 19T, port&polish 531 w/ 38exht valves, running E85, MS2 V3 Extra management system was until one year... Then back to Fred chips :P. -->280HP 2nd: T5 Swap: S70 B5254T engine with TD04HL-19T turbo. Goal is above 300HP on E85 fuel Details: Used Firmware: 1.1.80 + VemsTune Vems case is a 960 Motronic ECU Big 20x4 LCD Bosch 7057 Wideband Fuel supported by 65lb Siemens Deka's Volvo T6 COP's Stock 60-2 flywheel, VR sensor Stock CAM HALL sensor (according to logs, rising edge re-clocked between cyl 3&1) ------------------------------------------------------------ Config and logs: http://www.vems.hu/files/NitroX5/ ----------------------------------------------------------- http://i238.photobucket.com/albums/ff56/Nitrox5/2010/T5%20Project/T5.jpg http://i238.photobucket.com/albums/ff56/Nitrox5/2010/VEMS/DSC00057.jpg
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.