_____ | ____| | _| | |___ |_____|
_______ ( ___ ) | ( ) | | | | | | | | | | | | | | (___) | (_______)
## ## ## ## ## ## ###
_ _ ( ) ( ) | |_| | | _ | | | | | (_) (_)
## ## ##### ## ## ## ## ## ## ## ##
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: '''Welcome to NielsenRacing!''' ---- I've been looking around a while for a good aftermarket EMS. Getting to know MembersPage/SimonMarmander, who has tested three different EMS' on his car and finally dialing it in with the GenBoard led me to VEMS. After seeing the many uses and possibilities it has first hand, I just had to buy a v3.3 for myself. The number of sensor inputs is one of them. MembersPage/EmilLarsson helped me over the phone so I managed to find the 9 free ADC's. Thanks! This means lots of sensors, so the ECU will sens everything that happens; to control or prevent. Nice, perhaps I won't blow as many engines in the future as in the past, and if I do, at least I can log it and se why it happened. =) ---- '''The car:''' *1975 Volvo 242 Turbo '''Engine:''' *B23 block borred and stroked to 2.8L, 16V head, custom intake with slide throttle, NOS Pro Fogger system, Holset HX52 turbo, dry sump oil system, closed crankcase ventilation ---- '''2005-11-21''' My VEMS-setup for the B23/16V will be as follows: '''Sensor inputs:''' AMEGA 128: *ADC0: Battery Voltage Sensing *ADC1: WBO2 #1 *ADC2: TPS *ADC3: CLT *ADC4: MAT #1 *ADC5: MAP #1 (In Intake Runners) *ADC6: MAP #2 (In Plenum) *ADC7: MAF MCP3208: *CH1: Fuel Pressure #1 (Primary Injector Fuel rail @ Intake Ports) *CH2: Fuel Pressure #2 (Secondary Injector Fuel rail @ Plenum) *CH3: Fuel Pressure #3 (NOS) *CH4: Oil pressure *CH5: EGT #1 *CH6: Backpressure #1 (In Header Collector) *CH7: Backpressure #2 (In Down pipe @ WBO2 #1) *CH8: Crankcase Pressure DIGITAL: *VR #1 (Crank Trigger) *VR #2 (Cam Sync) *Knock #1 *Knock #2 You have many extra sensors. I guess you want to use MCP3208 channels to capture them. To build input protection and RC lowpass filters, a similar circuit is used: http://linkopingsmotorsport.se/vrtomic.gif * R1 = 10k resistor and * R2 = 220nF capacitor (not resistor, as on the schematic) * instead of the soundcard, the MCP3208 input pins used (pin1..8) * input goes to the node marked EC36pin27 If we put a few RC filters on a small breakoff-board in our next PCB-batch, we'll apply BAV99 diodes too, for extra protection. '''Outputs:''' *Coil-On-Plug 1,2,3,4 *Primary Injectors 1,2,3,4 *Secondary Injectors 1,2,3,4 *Boost Control (PWM) *Fuel Pump Relays (or PWM) *Electrical Water Pump Control (PWM) *NOS Solenoid Activation (RPM Window Switch IF @ WOT) *Cooling Fan Low Speed Relay *Cooling Fan High Speed Relay *Shift Light Control - make sure to use LEDs (not lamp) for fast operation. Either one big 10mm LED, or several smaller LEDs like a few dedicated in the [http://shop.x-dsl.hu/catalog/index.php?cPath=1_15 round cluster] ---- Feedback and comments are welcome! '''Christian Nielsen''' '''Bollebygd, SWEDEN''' Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.