##    
         
  ###    
   ##    
   ##    
   ##    
  ####   
         

         
         
  ####   
 ##      
 ##      
 ##      
  ####   
         

         
         
 #####   
 ##  ##  
 ##  ##  
 #####   
 ##      
 ##      

         
         
  #####  
 ##  ##  
 ##  ##  
  #####  
     ##  
 #####   

         
         
 #    #  
 #    #  
 #    #  
  #  #   
   ##    
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
It is indeed a 3B engine harness with 5 TFSi coils with the recovery of the signals from this one with the econoseal 10 pinout plug, the vems with the number 19229 and 9297 work correctly on Audi S2 3B "I only use the computer, the tablet and the phone are at the bottom of Lake Balaton... :)" -Audi S2 3B stroker setup -Turbo GTX3076R -2200cc injector E85 -Cam 7A - Cylinder head prepare under three angles -Super teak valve -Wossner piston -TFSi coil -Wagner collector -2.7 bar turbo pressure ---- '''Audi 3B engine harness with mot55 connector''' (actually Audi 3B is just a guess, is this correct ? Request did not even say "Audi", only "vehicle") Might want to enjoy [https://www.youtube.com/watch?v=JdZWlxMY6d4 this standup] I can't start the '''vehicle''' and nothing in the log. Everything works manually, but no boot. I have tried other 55 VEMS ('''what is the exact serialnumber of the working device ?''') on the vehicle, it starts instantly. What is the '''ignition setup ?''' * active coils need logiclevel outputs * passive coils need IGBT outputs ** 1 or 5 coils ? ** exact pins ? '''Please flush the phone/tablet down the toilet and use PC/notebook for communications for reasonable results.''' ---- Solution is simple, same firmware and config and identical HW=> it will start. Just need to check step by step. Please edit this project page, write or link all information about your engine and project (including measurements and config) thematically... '''Support is only possible if the most uptodate information is seen with no misunderstanding.''' * correct engine-and-harness must be used ** (verify, make measurements of GND, supply, and '''resistance of CLT and MAT sensors via the mot55 connector''', take note of estimated engine temperature) Note that there are PTC (default for 3B, around 400 Ohm at 25C) and NTC (around 2252 Ohm at 25C, not default but often used) type MAT sensor for Audi 3B engine. ---- * save known good config ** publish known good config on your page * save wrong config ** publish wrong config labeled as such * upload good config to Audi3B/8815 ECU config must be uploaded and perhaps adjusted according to the setup. '''2014 june specs when sent out''': * oid9204 audi3b/8815 VEMS motronic55 * Model: Audi 3B (+0.70EUR) * Knock input channels: 0 * MAT input: Audi factory PTC ** sensor resistance can be measured with sensor unplugged. Or through mot55 connector GND and sensor input (only unplug ECU with ignition off!) ---- Please see and read carefully : https://vems.hu/vt/help/main/error_reporting.html Updating your page to the best of your knowledge makes support possible. (update your page before any other form of communication). Please note that the 2022. 04. 20. email does not even contain the engine type, or even the word "Audi". (it does not look like enough information to even start anything). You might understand that exact information, as full as possible is the key to success. ---- '''message sent via email (might not arrived) Support is always through wiki page. (not via email) Generic instructions : http://www.vems.hu/wiki/index.php?page=MembersPage (eg. so you can create more wiki pages easily). Please edit your page, write or link all information about your engine and project (including measurements and config) thematically... Support is only possible if the most uptodate information is seen with no misunderstanding. correct engine-and-harness must be used (verify, make measurements of GND, supply, and resistance of CLT and MAT sensors via the mot55 connector, take note of estimated engine temperature) Note that there are PTC (default for 3B, around 400 Ohm at 25C) and NTC (around 2252 Ohm at 25C, not default but often used) type MAT sensor for Audi 3B engine. save known good config publish known good config on your page save wrong config publish wrong config labeled as such upload good config to Audi3B/8815 ECU config must be uploaded and perhaps adjusted according to the setup. oid9204 6 audi3b/8815 VEMS motronic55 - Service: normal - with_LSU4sensor: no - Model: Audi 3B (+0.70EUR) - Knock input channels: 0 - MAT input: Audi factory PTC 2014 june Please see and read carefully : https://vems.hu/vt/help/main/error_reporting.html Updating your page to the best of your knowledge makes support possible. (update your page before any other form of communication). Please note that the 2022. 04. 20. email does not even contain the engine type, or even the word "Audi". (it does not look like enough information to even start anything). https://www.youtube.com/watch?v=JdZWlxMY6d4 might be cool :-) You might understand that exact information, as full as possible is the key to success. regards, ...
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.