____  
 |  _ \ 
 | | | |
 | |_| |
 |____/ 
        

         
         
  ####   
 #    #  
 ######  
 #       
  ####   
         

 ______  
(  __  \ 
| (  \  )
| |   ) |
| |   | |
| |   ) |
| (__/  )
(______/ 
         

 ______  
(  ___ \ 
| (   ) )
| (__/ / 
|  __ (  
| (  \ \ 
| )___) )
|/ \___/ 
         

           
     /\    
    /  \   
   / /\ \  
  / ____ \ 
 /_/    \_\
           
           

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
For Audi 20VT engines the following triggers make sense: * factory (135 crank, 1 crank, 1 cam) * 60-2 - easy to install gasket at the flywheel * 5 cranktooth, 1 cam For this engine, without consultation, 10 crankteeth were made. This has no advantage, only disadvantages. Config changes are needed. After 1 tooth broke off, it became 10-1. Upload config dump, so we can review. Notes: * tooth_wheel_twidth=90 ('''36 degrees''' ! 18 degrees as in your config is simply bad) * Nminus1 flag must be set (primary_trigger=11 not 01) * camsync position must not be too close to missing tooth ! oscilloscoping needed? * in worst case another 4 can be removed so it will become a 5+1 trigger Is this 1.1.27 ? primep=00 primep_temp_scaling=00 cwl=46 cwh=0F cranking_thres=03 awev=0F awev_temp_scaling=1A awec=32 warmup_clt_range[0]=00 warmup_clt_range[1]=10 warmup_clt_range[2]=24 warmup_clt_range[3]=38 warmup_clt_range[4]=50 warmup_clt_range[5]=64 warmup_clt_range[6]=78 warmup_clt_range[7]=8C warmup_clt_range[8]=AA warmup_clt_range[9]=C8 warmup_clt[0]=B1 warmup_clt[1]=A9 warmup_clt[2]=9B warmup_clt[3]=8F warmup_clt[4]=87 warmup_clt[5]=82 warmup_clt[6]=78 warmup_clt[7]=71 warmup_clt[8]=6A warmup_clt[9]=64 warmup_rpm_scale=FF req_fuel=2A divider=01 alternate=14 injopen=00 battfac=13 kpafac=CD kpaoffs=8E injocfuel=19 injrampup_battfac=FF injpwm=FF injpwmt=FF als_launch_input=CF rpmk[0]=09 rpmk[1]=60 tpsdot_kpadot_conf=00 tpsdotrate[0]=05 tpsdotrate[1]=0A tpsdotrate[2]=14 tpsdotrate[3]=28 tpsaq[0]=01 tpsaq[1]=01 tpsaq[2]=01 tpsaq[3]=01 als_cut_mintps=00 tpsasync=01 acmult=C8 tpsacold=05 launch_enrich=03 launch_retard=00 overrun_fuelcut=63 overrun_fuelresume=62 rev_limit=50 airden_ignore=60 config11=41 config12=40 config13=02 batt_cal=C0 fastidle=00 als_max_cut=00 dbaro=0C tps_low=30 tps_high=FA fan_temp=5F fan_hyst=05 fan_channel=FF iac_step_seq=C9 iac_conf=00 iac_max_steps=E0 iac_tps_thres=05 iac_cold_idle_temp=87 iac_warm_idle_temp=CF iac_cold_rpm=19 iac_warm_rpm=10 iac_cold_start_pos=E2 iac_warm_start_pos=B0 iac_afterstart_rpm=1F iac_afterstart_duration=64 iac_speed=05 iac_kp=14 iac_ki=0F iac_kd=14 launch_rpm=32 iac_integral_limit_dec=05 iac_integral_limit_inc=78 iac_integral_deadband=0A iac_deadband=05 als_cut_maxtps=00 iac_overclose_interval=FF iac_ref_pos[0]=36 iac_ref_pos[1]=33 iac_ref_pos[2]=33 iac_ref_pos[3]=33 iac_ref_pos[4]=30 iac_ref_pos[5]=30 iac_ref_pos[6]=2E iac_ref_pos[7]=2E iac_ref_pos[8]=2E iac_ref_pos[9]=2B iac_sol_channel=7F iac_ign_slope=20 softrpm_range=26 iac_ign_advance_limit=08 iac_ign_retard_limit=08 iac_ign_threshold=08 ego_conf=06 ego_lag=01 ego_coolant=00 ego_maxtps=FF ego_maxmap=FF ego_minrpm=06 ego_maxrpm=FF ego_warmup=01 ego_lean_limit=08 ego_rich_limit=05 ego_pid_kp=28 als_enrich=00 ego_delta=03 ego_target=D5 ego_pid_window=FF wbo2_warmup_ramp=C0 als_react_tps=FF wbo2_abs_limit=F5 wbo2_limit_maxt=A0 wbo2_fallback=6E wbo2_retry_t=06 als_retard_rpm1=BA als_retard_rpm2=50 wbo2_ri_target=9A wbo2_nernstdc_target=89 wbo2_pump_pw_zero=64 wbo2_calibration=AB wbo2_heater_pid_kp=46 wbo2_heater_pid_ki=10 wbo2_heater_pid_kd=1A wbo2_heater_pid_ilimit=80 wbo2_pump_pid_kp=15 wbo2_pump_pid_ki=37 wbo2_pump_pid_kd=00 wbo2_pump_pid_ilimit=FF wbo2_ri_confidence_scale=80 '''knock_chan=00''' use F0 not 00 knock_sampling_window=FF knock1_frequency=29 knock1_gain=FF knock1_integrator=FF knock2_frequency=29 knock2_gain=FF knock2_integrator=FF knock_threshold=FF knock_noise_scale=FF knock_max_retard=00 knock_default_retard=00 knock_retard_step=00 knock_retard_delay=00 knock_advance_step=00 knock_advance_delay=00 knock_minrpm=FF knock_maxrpm=FF ve_learn_coolant=D8 ve_learn_max_power=FF ve_learn_rpm_scale=1E ve_learn_kpa_scale=1E ve_learn_ego_scale=43 ve_learn_min_weight=4D ve_learn_speed=FF ve_learn_limit=33 ve_learn_conf=00 lcd_c0=FE lcd_delay=CC lcd_backlight=FF kpa_conf=22 als_igncut_rpm2=64 als_retard_mintps=00 als_retard_maxtps=00 lcd_default_view=00 primary_trigger=11 secondary_trigger=19 tooth_wheel=09 trigger_tooth=00 another_trigger_tooth=04 crank_minper=00 '''tooth_wheel_twidth1=48''' use 90 not 48 ! tooth_wheel_twidth2=00 cam_sync_r_edge_phase=00 cam_sync_f_edge_phase=00 reset_engphase_after=00 ign_tdcdelay=82 ign_dwell14=34 ign_dwell6=25 ign_crank_advance=00 ign_out=70 ignchmax=04 engine_off_delay=0F pump_on_mintime=0B fuelpump_channel=5F inj_stage2_rate=FF inj_stage2_start_tps=FF inj_stage2_start_map=FF als_igncut_rpm1=FF als_deact_time=00 als_deact_egt=00 als_retard=00 als_rev_limit=FF misc1out_minrpm=3F misc1out_maxrpm=FF misc1out_mintps=00 misc1out_maxtps=FF misc1out_minmap=00 misc1out_maxmap=FF misc1out_channel=52 misc2out_minrpm=00 misc2out_maxrpm=FF misc2out_mintps=66 misc2out_maxtps=FF misc2out_minmap=00 misc2out_maxmap=FF misc2out_channel=0F act_wot_rpm=FF act_wot_channel=FF act_rpm_rpm=47 act_rpm_channel=6F egt1_cal=4C als_tks_channel=FF boost_conf=59 boost_targetoffs=1E boost_minpressure=3C boost_pid_kp=B4 boost_pid_ki=46 boost_pid_kd=23 boost_pid_ilimit=4B boost_channel=7F water_pump_temp=00 hybrid_rpm_a=00 hybrid_rpm_m=00 water_pump_hyst=00 water_pump_channel=FF toothrel_normal=60 toothrel_missing=00 fuelcut_min_kpa=0A fuelcut_max_kpa=96 tach_channel=70 tach_div=14 shiftcut_conf=00 shiftcut_channel=FF shiftcut_time=00 softrpm_rpm=42 j[0]=6180 6180 6080 6380 6F80 7880 7B80 7B80 7680 7280 6E80 6680 j[1]=6380 6380 6380 7780 6E80 7680 7980 7A80 7680 7380 6F80 6580 j[2]=6280 6180 6180 8080 6C80 7480 7880 7980 7580 7180 6E80 6580 j[3]=6180 6180 6180 7F80 6A80 7380 7980 7980 7680 7280 6E80 6580 j[4]=6180 6180 6180 7E80 6980 7380 7A80 7B80 7780 7380 6F80 6780 j[5]=5E80 5E80 5E80 7680 6980 7480 7C80 7D80 7980 7480 6E80 6780 j[6]=5C80 5C80 5B00 6A80 6780 7380 7C80 7D80 7A80 7680 6E80 6680 j[7]=5A80 5980 5980 5880 6580 7280 7A80 7D80 7B80 7580 6F80 6480 j[8]=5780 5780 5680 5580 6280 6F80 7880 7A80 7A80 7580 6E80 6280 j[9]=5780 5780 5580 5280 5A80 6980 7380 7880 7880 7380 6F80 6280 j[A]=5980 5780 5864 5380 5580 6480 7080 7380 7480 6F80 6A80 6080 j[B]=5A80 5A80 5980 5580 5880 6280 6C80 6F80 7180 6D80 68A1 6080 l[0]=47 47 47 47 47 47 47 47 47 47 47 47 l[1]=47 47 47 47 47 47 47 47 47 47 47 47 l[2]=48 48 48 48 48 48 48 48 48 48 48 48 l[3]=48 48 48 48 48 48 48 48 48 48 48 48 l[4]=48 48 48 48 48 48 48 48 48 48 48 48 l[5]=55 55 55 55 55 55 55 55 55 55 55 55 l[6]=66 66 66 66 66 66 66 66 66 66 66 66 l[7]=6D 6D 6D 6D 6D 6D 6D 6D 6B 6B 6D 6D l[8]=7B 7B 7B 7B 7B 7B 7B 7B 7B 7B 7B 7B l[9]=7B 7B 7B 7B 7B 7B 7B 7B 7B 7B 7B 7B l[A]=83 83 83 83 83 83 83 83 83 83 83 83 l[B]=83 83 83 83 83 83 83 83 83 83 83 83 n[0]=38 38 5C 84 90 90 90 90 90 90 90 83 n[1]=38 38 54 81 8F 90 90 8C 90 90 90 90 n[2]=34 34 4E 7D 8C 8F 90 90 90 90 90 90 n[3]=30 32 4C 79 88 8D 8F 90 90 90 90 90 n[4]=30 38 4E 75 83 8A 8D 8E 8F 8F 8F 8F n[5]=2C 35 50 6D 7B 82 84 84 86 86 86 85 n[6]=22 29 48 67 73 7A 7C 7C 7D 7D 7D 7D n[7]=12 11 38 61 69 6E 70 71 73 74 74 74 n[8]=0D 0D 2A 58 5D 62 63 64 66 67 67 67 n[9]=0B 0B 22 4B 50 53 54 55 57 58 58 58 n[A]=0A 0A 1B 44 44 41 3F 3F 40 41 41 40 n[B]=04 04 13 3A 39 34 31 31 2E 2F 30 2E k[0]=0A 14 1E 28 32 43 53 64 75 85 91 9B r[0]=07 0C 0F 14 1E 28 32 37 41 46 4B 55 h[0]=04 10 08 02 01 20 40 80 h[1]=10 0C 08 04 00 00 00 00 h[2]=30 20 10 00 40 00 00 58
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.