#    
 ######  
   ##    
   ##    
   ##    
   ## #  
    ##   
         

   ____ 
  / ___|
 | |  _ 
 | |_| |
  \____|
        

   ##    
    #    
    #    
    #    
    #    
    #    
   ###   
         

   ##    
         
  ###    
   ##    
   ##    
   ##    
  ####   
         

   _____ 
  / ____|
 | (___  
  \___ \ 
  ____) |
 |_____/ 
         
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Back to MembersPage/NanassyPeter ---- '''Pending''' * MAT ignition retard. * custom oil temp/pressure gauge with V3.3 and LCD should check the relevant page, IIRC these are not yet implemented ---- ----- GenBoard/UnderDevelopment/StagedInjectors * 5 primary injectors, driven sequentially * and another 5 staged. (note: 2 free injector drivers on this 5cyl engine, because fuelpump switched from an injector channel as well). '''Document the flowrate of injectors - the ratio of primary and secondary is very important because it must be configured''' We have 10 Audi S3/TT high impedance (14ohm) 420ccm "shorty" injectors.So basically we run the same in the staged group as in the sequential "main" injector group. ** Possibly 5 connected (while the FET and EC36xx pin would be happy to drive 5 injectors, highz or properly configured lowz, but this could abuse the flyback. ** or 2+3 split. This is recommended. It's OK to switch them simultaneously though, like h[0]=xx xx xx xx xx xx xx 60 where 60 (decimal 96) is sum of 20 and 40 (decimal 32 and 64) to switch injF and injG (see GenBoard/Manual/DigitalOut/Table) Sorry ,this section is totally chinees for me.... Please explain it a bit more. Is it possible to configure fuel pump out to another "thing",to have all 8 injector FETs? How this works on a V8 engine ,where all 8 injectors have to be driven independently? * I have 8 separately driven injectors with the fuel pump fed separately. See MembersPage/DavidBlades/FanTest for my config. Anyway,is there any difference between: 1 inj FET driving 2 injectors VS. 1 inj FET driving 3 injectors?? What injector behaviour can i expect if i drive 2 injectors from 1 inj FET,this way i do not need staging,all injectors will work all the time.There is NO NEED for lean idle,this is a race project.Im basically looking for options here.... '''A:''' We have driven 3,4 and 5 high-z injectors on the same outputs on a few cars. With the powerflyback board you will most likely have no problem with driving those high-z injectors in pairs. They aren't too big. //Emil ---- How can i insert the new ALS functions (MembersPage/GaborRacz/NewAlsLaunchAndOthers) in the 1.0.30firmware and Megatune?? ---- I still experience some unwanted EGO behaviour sometimes,the EGO correction just switches off (no correction at all),even tough it would be needed! Please tell me which MegaTune variable to set and which direction??And what is this all about?
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.