_________
\__   __/
   ) (   
   | |   
   | |   
   | |   
   | |   
   )_(   
         

 _       _ 
( )  _  ( )
| | ( ) | |
| | | | | |
| (_/ \_) |
`\___x___/'
           
           

 _   _ 
| \ | |
|  \| |
| . ` |
| |\  |
\_| \_/
       
       

         
  ####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  ####   
         

         
|\     /|
| )   ( |
| | _ | |
| |( )| |
| || || |
| () () |
(_______)
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Marcell,please call me when you finished my new ECU. ----- *Wiring complete,sensors working,i can see the gauges in Megatune,but there is no RPM signal yet (can wrong calibration (60-2 instead of 5 window) cause this?) * primary_trigger=FF (or FE if falling edge is used). The primary_trigger=01 is for multitooth (eg 60-2 missing-tooth) setup * secondary_trigger=02 must be used. But hey, this is appears on almost every pages of yours ! * TPS reads 10% after calibration,is this normal? ** of course NOT! increase tps_low ---- '''wishes for next v3.x ECM''' *tachometer output (weryimportant for 5 coil config) * primary trigger: VR crank 60-2 (changeable to HALL with dip switch if possible, so only the endplate needs to be removed) secondary 1 window hall camsync * High voltage flyback (2+6diode) * All 8 ignition/injector channels * EGT and Knock * 4bar MAP sensor onboard * Programmable Shift light output (a p259 channel) * baro (altitude) compensation: MAP measurement at startup. Separate baro sensor is not justified when you have WBO2: when we tune at (say) 200m above sea level, we add +10% fuel in the VE table, so ego_correction=-10% (-25 on display) that is good to appr. 5000m, and normally the WBO2 based ego correction will take away as much of the extra fuel as necessary. '''under investigation:''' * WBO2 analog output (for DVM or other ECM), eg. ** lambda=0.6 .. 1.45 => 0.6V .. 1.45V ** 1.45V .. 1.499V not used ** O2%=15..21% => 1.5V .. 2.1V (or should it be max 1.96V so the DVM can be left in 2V mode? maybe configurable) ** below < 0.55V: measurement error (eg. WBO2 sensor not heated). Alternatively this condition could be mapped to >2.5V for better margin, but when WBO2 controller is unpowered, 0V is "easier" to maintain * Warning light output: activates when any measured data (that I list here) exceeeds it's programmable warning treshold: ** CLT: engine too hot ** EGT: exhaust too hot ** MAP: boost too high (BoostController misconfigured, or pneumatic problem) ** ... ---- Problem: 4 out of 10 startup is unsuccesfull.LCD displays silly things and car runs like SH!T! sometimes after succesfull starting LCD displays some kind of table datas instead of realtime datas (as usually),but no keybord is connectec.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.