### ##  
 #  #  # 
 #  #  # 
 #  #  # 
 #  #  # 
         

 _     
( )    
| |    
| |  _ 
| |_( )
(____/'
       
       

       
/'\_/`\
|     |
| (_) |
| | | |
(_) (_)
       
       

   ###   
  ## ##  
  ##     
 ####    
  ##     
  ##     
 ####    
         

         
 ##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Back to MembersPage/NanassyPeter '''15 minus 1 trigger installed on Inline 5 Audi engine''' Primary trigger is a 15-1 (yes, missing tooth!) crankwheel with [http://shop.vems.hu/catalog/product_info.php?cPath=1_12&products_id=107 GT101 HALL sensor] (which pulls down when it detects ferromagnetic material and leaves the signal high in the gap, as pulled up by the pullup resistor). * either falling or rising edge is OK with this, but falling is "sharper", so * primary_trigger=10 # (decimal 16); which means ** falling edge ** multitooth ** no filtering ** advanced filter off ** N-1 (N minus 1 active!!!) The falling edge (metal coming in) right after the missing tooth is 2 teeth+60degs = 48 crankdeg + 60 crankdeg = 108 crankdegrees BEFORE TOP DEAD CENTER (Cyl 1 ?) , yes ,cyl 1. '''Secondary trigger (HALL)''' Pulse (falling or rising edge?) is set 10deg BEFORE primary trigger missing tooth. * trigger_tooth=02 # 00 .. 03 might be candidate, a good variable to play with * another_trigger_tooth=06 # next trigger tooth; 06 for sure * ign_tdcdelay=78 # (decimal 120) ign TDC-delay: 60deg ; should be fine first, adjust for good base timing when it runs * normal tooth width=1 * missing tooth width=2 * reset_engphase_after=1e # engine phase when to reset=30 ---- While we were lucky enough to get the engine running with totally misconfigured values (another_trigger_tooth=03 and reverse sequence ;-), it was running really poor and showed 2x higher RPM (than real). firmware version= 1.0.45 Both mcd and mct are important to reproduce. '''mcd''' * alternate=04 * ignchmax=04 '''mct''' h[2]=01 00 02 04 03 .. .. ... * ign sequence ** ignch1 cyl2 doesn't fire ** ignch0 cyl1 doesn't fire ** ignch2 cyl3 ** ignch4 cyl5 ** ignch3 cyl4 mcdmct together Hello> primep=00 primep_temp_scaling=00 cwl=32 cwh=0A cranking_thres=02 awev=00 awev_temp_scaling=00 awec=00 warmup_clt_range[0]=00 warmup_clt_range[1]=12 warmup_clt_range[2]=26 warmup_clt_range[3]=3A warmup_clt_range[4]=50 warmup_clt_range[5]=64 warmup_clt_range[6]=78 warmup_clt_range[7]=8C warmup_clt_range[8]=AA warmup_clt_range[9]=C8 warmup_clt[0]=B4 warmup_clt[1]=AC warmup_clt[2]=A0 warmup_clt[3]=90 warmup_clt[4]=87 warmup_clt[5]=83 warmup_clt[6]=7F warmup_clt[7]=71 warmup_clt[8]=6B warmup_clt[9]=64 warmup_rpm_scale=BF req_fuel=21 divider=01 alternate=14 injopen=00 battfac=13 kpafac=CD kpaoffs=8E injocfuel=0D injrampup_battfac=FF injpwm=FF injpwmt=FF injpwm6=0A rpmk[0]=09 rpmk[1]=60 tpsdot_kpadot_conf=00 tpsdotrate[0]=24 tpsdotrate[1]=3D tpsdotrate[2]=55 tpsdotrate[3]=82 tpsaq[0]=0D tpsaq[1]=16 tpsaq[2]=20 tpsaq[3]=2D als_cut_mintps=73 tpsasync=02 acmult=C8 tpsacold=96 launch_enrich=00 launch_retard=1C overrun_fuelcut=46 overrun_fuelresume=41 rev_limit=54 airden_ignore=00 config11=41 config12=40 config13=02 batt_cal=BD fastidle=00 als_max_cut=65 dbaro=0C tps_low=0E tps_high=A3 fan_temp=5F fan_hyst=05 fan_channel=FF iac_step_seq=C9 iac_conf=00 iac_max_steps=E0 iac_tps_thres=54 iac_cold_idle_temp=87 iac_warm_idle_temp=CF iac_cold_rpm=19 iac_warm_rpm=10 iac_cold_start_pos=E2 iac_warm_start_pos=B0 iac_afterstart_rpm=1F iac_afterstart_duration=64 iac_speed=05 iac_kp=14 iac_ki=0F iac_kd=14 launch_rpm=34 iac_integral_limit_dec=05 iac_integral_limit_inc=78 iac_integral_deadband=0A iac_deadband=05 als_cut_maxtps=A6 iac_overclose_interval=FF iac_ref_pos[0]=36 iac_ref_pos[1]=33 iac_ref_pos[2]=33 iac_ref_pos[3]=33 iac_ref_pos[4]=30 iac_ref_pos[5]=30 iac_ref_pos[6]=2E iac_ref_pos[7]=2E iac_ref_pos[8]=2E iac_ref_pos[9]=2B iac_sol_channel=7F iac_ign_slope=20 softrpm_range=12 iac_ign_advance_limit=08 iac_ign_retard_limit=08 iac_ign_threshold=08 ego_conf=06 ego_lag=01 ego_coolant=B4 ego_maxtps=E6 ego_maxmap=FF ego_minrpm=06 ego_maxrpm=FF ego_warmup=3C ego_lean_limit=03 ego_rich_limit=03 ego_pid_kp=28 als_enrich=1A ego_delta=1A ego_target=19 ego_pid_window=FF wbo2_warmup_ramp=C0 als_react_tps=00 wbo2_abs_limit=F5 wbo2_limit_maxt=A0 wbo2_fallback=60 wbo2_retry_t=06 wbo2_edgetime_corr=BA wbo2_edgetime_min=50 wbo2_ri_target=9A wbo2_nernstdc_target=89 wbo2_pump_pw_zero=64 wbo2_calibration=D9 wbo2_heater_pid_kp=46 wbo2_heater_pid_ki=10 wbo2_heater_pid_kd=1A wbo2_heater_pid_ilimit=80 wbo2_pump_pid_kp=15 wbo2_pump_pid_ki=37 wbo2_pump_pid_kd=00 wbo2_pump_pid_ilimit=FF wbo2_ri_confidence_scale=80 knock_conf=01 knock_sampling_window=FF knock1_frequency=29 knock1_gain=FF knock1_integrator=FF knock2_frequency=29 knock2_gain=FF knock2_integrator=FF knock_threshold=FF knock_noise_scale=FF knock_max_retard=00 knock_default_retard=00 knock_retard_step=00 knock_retard_delay=00 knock_advance_step=00 knock_advance_delay=00 knock_minrpm=FF knock_maxrpm=FF ve_learn_coolant=D8 ve_learn_max_power=FF ve_learn_rpm_scale=1E ve_learn_kpa_scale=1E ve_learn_ego_scale=43 ve_learn_min_weight=4D ve_learn_speed=FF ve_learn_limit=33 ve_learn_conf=00 lcd_c0=FE lcd_delay=FF lcd_backlight=FF kpa_conf=22 ign_balance=64 als_retard_mintps=99 als_retard_maxtps=CC lcd_default_view=00 primary_trigger=D0 secondary_trigger=10 tooth_wheel=0E trigger_tooth=02 another_trigger_tooth=06 crank_minper=00 tooth_wheel_twidth1=00 tooth_wheel_twidth2=00 cam_sync_r_edge_phase=00 cam_sync_f_edge_phase=00 reset_engphase_after=1E ign_tdcdelay=8C ign_dwell14=2F ign_dwell6=43 ign_crank_advance=28 ign_out=70 ignchmax=04 engine_off_delay=0F pump_on_mintime=0B fuelpump_channel=5F inj_stage2_rate=FF inj_stage2_start_tps=FF inj_stage2_start_map=FF als_deact_rpm=1E als_deact_time=00 als_deact_egt=00 als_retard=F0 als_rev_limit=FF misc1out_minrpm=00 misc1out_maxrpm=FF misc1out_mintps=00 misc1out_maxtps=FF misc1out_minmap=00 misc1out_maxmap=FF misc1out_channel=7F misc2out_minrpm=FF misc2out_maxrpm=FF misc2out_mintps=00 misc2out_maxtps=FF misc2out_minmap=00 misc2out_maxmap=FF misc2out_channel=6F act_wot_rpm=FF act_wot_channel=FF act_rpm_rpm=48 act_rpm_channel=60 egt1_cal=4C als_tks_channel=FF boost_conf=59 boost_targetoffs=1E boost_minpressure=3C boost_pid_kp=B4 boost_pid_ki=46 boost_pid_kd=23 boost_pid_ilimit=4B boost_channel=70 water_pump_temp=00 hybrid_rpm_a=00 hybrid_rpm_m=00 water_pump_hyst=00 water_pump_channel=FF toothrel_normal=00 toothrel_missing=00 fuelcut_min_kpa=0A fuelcut_max_kpa=FF tach_channel=FF tach_div=FF shiftcut_conf=00 shiftcut_channel=00 shiftcut_time=3F softrpm_rpm=52 j[0]=3380 3480 3780 3880 3980 3C80 3D80 3D80 3D80 3D80 3C80 3980 j[1]=3780 3780 3C80 3B80 3D80 4080 4080 4480 4480 4480 4480 4680 j[2]=3A80 3A80 4280 4280 4280 4680 4780 4B80 4B80 4A80 4A80 4A80 j[3]=5280 5480 5380 4F80 4F80 4F80 5280 5480 5280 5280 5280 5080 j[4]=5E80 5D80 5D80 5C80 5980 5980 5B80 5C80 5A80 5B80 5A80 5980 j[5]=6680 6680 6680 6380 6380 6780 6780 6780 6980 6980 6880 6580 j[6]=7080 6F80 7080 7080 7080 7380 7180 7280 7280 7180 7280 7080 j[7]=7D80 7C80 7C80 7C80 7980 7980 7A80 7980 7880 7780 7880 7880 j[8]=8080 8080 8180 8280 8280 8280 8280 8280 8280 8280 8280 8280 j[9]=8580 8580 8380 8580 8A80 8A80 8A80 8880 8880 8880 8880 8880 j[A]=8780 8780 8780 8480 8C80 8C80 8C80 8A80 8A80 8A80 8A80 8A80 j[B]=8B80 8B80 8B80 8980 8C80 8E80 8E80 8C80 8C80 8C80 8C80 8C80 l[0]=47 47 47 47 47 47 47 47 47 47 47 47 l[1]=47 47 47 47 47 47 47 47 47 47 47 47 l[2]=48 48 48 48 48 48 48 48 48 48 48 48 l[3]=48 48 48 48 48 48 48 48 48 48 48 48 l[4]=48 48 48 48 48 48 48 48 48 48 48 48 l[5]=48 43 43 43 43 43 43 43 43 43 43 43 l[6]=5C 5C 5C 5C 5C 5C 5C 5C 5C 5C 5C 5C l[7]=5C 5C 5C 5C 5C 5C 5C 5C 5C 5C 5C 5C l[8]=5E 5E 5E 5E 5E 5E 5E 5E 5E 5E 5E 5E l[9]=63 63 63 63 63 63 63 63 63 63 63 63 l[A]=70 70 6D 6D 6D 70 6D 6D 70 6D 70 70 l[B]=7E 7E 7E 7E 7E 7E 87 87 87 7E 7E 7E n[0]=38 38 6C 89 9D A4 A7 A9 AB AB AB AC n[1]=38 38 69 85 97 9F A3 A5 A8 A8 A9 A9 n[2]=38 38 65 7F 93 9B A1 A1 A4 A4 A8 A8 n[3]=40 3F 60 79 90 99 9E A0 A1 A2 A5 A6 n[4]=40 3E 63 7D 8F 98 9E 9E 9E 9E A1 A2 n[5]=3C 45 5E 75 86 8F 93 93 95 97 99 9A n[6]=32 39 54 6A 77 7E 86 89 8C 8D 90 92 n[7]=22 21 3A 57 6B 7A 7F 84 88 8B 8E 8E n[8]=1D 1D 2E 45 64 70 78 7C 80 84 88 88 n[9]=1B 1B 29 3A 60 70 78 78 7C 80 84 84 n[A]=1A 1A 25 37 4C 5C 60 64 68 6C 70 74 n[B]=14 14 14 19 20 27 2D 31 36 39 3B 3E k[0]=0A 14 1E 28 32 43 53 64 75 85 9B A7 r[0]=07 0C 0F 14 1E 28 32 37 41 46 4B 55 h[0]=04 10 08 02 01 00 40 80 h[1]=00 00 00 00 00 00 00 00 h[2]=01 00 02 04 03 07 07 07 b[0]=7D 82 82 96 96 96 96 96 96 96 96 96 t[0]=FF FF FF FF FF FF FF FF
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.