_____ 
  / ____|
 | |     
 | |     
 | |____ 
  \_____|
         
         

 _______ 
(  ____ \
| (    \/
| |      
| |      
| |      
| (____/\
(_______/
         

   ##    
         
  ###    
   ##    
   ##    
   ##    
  ####   
         

         
|\     /|
| )   ( |
| (___) |
|  ___  |
| (   ) |
| )   ( |
|/     \|
         

         
         
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Audi 5 cyl 20vt AAN engine '''Please disable Motorsport/Camshaft angle control/third trigger=disable''' * burn * reboot ** note: the third trigger is connected for diagnostic, and useful for verifying cam-HALL position relative to crankhome-VR ** but '''only the secondary and primary trigger must be enabled during normal operation, the third trigger should be disabled''' for normal operation in this case (== audi with a cylinder head without camshaft-angle-control = no VVTI) ---- note: use FileArea to upload files (under http://www.vems.hu/files/MembersPage/MorneAudi/morne/ where the other related files are). '''RPM=0 => Tools/capture triggerlog''' so we can see which trigger seem to be missing * [http://vems.hu/vemstune/bugreports/reports.php?cmd=view&key=oKLJqH#comments vemscfg can be found in the report zipfile] ** [http://vems.hu/files/MembersPage/MorneAudi/morne/ vemscfg file], also default AAN file and the "diff -U2" difference ** no serious problem in the configuration at first glance: ** prohibit seems good for 1.1.96 ** configswitch is disabled ** some calibration values differ (good) * '''vemslog: STILL not available''' ** click on "LOG" icon until it becomes green, attempt startup, publish the related file from VEMS_Files directory * '''triggerlog: not available''' (important if RPM=0) ** '''Tools/Capture triggerlog, attempt startup, publish the related file from VEMS_Files directory''' * we would need to check the '''RPM at the startup attempt''' ! ** is RPM=0 at startup ? ** or RPM=normal (around 180) ? Or nonzero, but abnormal (if so, how) ? ---- '''Ignition outputs...''' * Ignition outputs visual, switch to test mode ** '''important if RPM is good at startup attempt''' * Did you see spark ? (use a sparkplug on the cylinderhead, make sure sparkplug-body is actually grounded to cylinder head). Do not touch ! * '''All 5 High-Voltage channels work correctly ''' ** yes, sparking OK Be careful ! * maybe it's something as simple as blown fuse ? See [http://vems.hu/vt VT help] and tutorial videos. ---- '''Measurements''' Note: triggerlog was not uploaded, but the images show something surprising: * The "Camshaft exhaust" is surprising (1 tooth for every 90 primary trigger tooth is OK, it's 270 divby3), we're investigating why it is not "secondary trigger". http://www.vems.hu/files/MembersPage/MorneAudi/morne/audiAANnew_sensor_log.png http://www.vems.hu/files/MembersPage/MorneAudi/morne/audi.png Copied from [http://vems.hu/vemstune/bugreports/reports.php?cmd=view&key=KlHx4b report] (note: vemslog was not captured or not included in this report either) log for audi s4 aan ignition coils tested ok measurement sensor ohm between 44/30 ,728kohm ohm between 45/30 2,69kohm aan pin 10 0,4ohm aan pin 19 1,3ohm aan pin 24 1,2ohm aan sensor pin 30 4,7mohm * measurement trigger 49/48 1kohm ** '''ALSO MEASURE pin49 DC voltage''' (ignition on, engine off) * measurement trigger 47/48 1kohm ** '''ALSO MEASURE pin47 DC voltage''' (ignition on, engine off) * '''aan sensor triger 48 open''' ** What does this mean ? Sounds to contradict the above 2 measurements (if "open", then it would be infinite ohm, not 1 kohm Symptoms * no start * 5 sparks tested OK * '''no rpm signal''' ** Assuming RPM=0 * do not know which firmware has been used Hi there, please find voltage measurement as requested. Pin 49 0volt ignition off, ECU connected. Pin 49 2.865volt ignition on, ECU connected. Pin 47 0volt ignition off, ECU connected. Pin 47 0volt ignition on, ECU connected. Pin 48 on harness tested infinity to earth. But test 1 kohm to pin 47 and 49 on G4 and G28 sensors. New log file has been send on 26/06/2012. Let me know if there was a problem again on the log file.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.