####   
 ##      
 ##      
 ##      
  ####   
         

         
  #### # 
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
     ### 

         
         
 ######  
    ##   
   ##    
  ##     
 ######  
         

         
         
  ### #  
 #   ##  
 #   ##  
  ### #  
      #  
  ####   

         
         
 #####   
 ##  ##  
 ##  ##  
 #####   
 ##      
 ##      

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
My daily driver, Audi S6 avant -95, 2.3L inline 5, 20 valve turbocharged engine (AAN). Going to install VEMS as direct replacement of original ECU (see PlugAndPlayMotronic) using factory wiring. Extra wires are needed only for WBO2. ---- My config.txt and tables.txt: [http://www.vems.hu/files/MembersPage/MiskaPeippo/AudiS6/config.txt config.txt] [http://www.vems.hu/files/MembersPage/MiskaPeippo/AudiS6/tables.txt tables.txt] ---- Flying wire adaptor for basic functionality from genboard (v3.3) towards motronic connector (pins Mxx) * 5x high-Z injectors (INJA..E to M36,M17,M34,M35,M16) * 5x ignition coils (with power output stages) (M01, M02, M23, M20, M21) * BoostControl solenoid aka WGFV (M33) * Idle air controller (M04) * Fuelpump relay (M03) * 3x trigger signals, 2x VR (M47 home signal, M49 rpm, M48 GND) + 1x hall (M08), InputTrigger/AudiTrigger setup * GND and Supply voltages ** to board itself with additional relay ** 5V to hall, TPS (EC36/28 to M12) * TPS sensor (M53) * CLT (M45), IAT (M44) sensors * Tachometer (M40) * Knock sensor Will add wiring diagram later.. Hardware changes made to V3.3 board * Trigger related ** R182 shorted (instead of 100k in primary trigger) ** 10k pullup to 5V for secondary VR signal * All ign channels changed to logic level ---- '''Config notes''' * injpwm=FF # highZ injectors * req_fuel=50 # is that for max VE = appr 200 ? * cwl=5A # might be close * cwh=19 # maybe a bit high but you'll see when it warms up :-) * primep=26 # give it a little (3.8msec) in cold * primep_temp_scaling=00 # but not with hot clt * awev=0D # try to increase, upto 40 (+64%), especially when warmup and other tables are unknown yet * awev_temp_scaling=80 * ... ouch, why are we guessing? A similar engine is running: MembersPage/NanassyPeter/Config so use Peter's config. just update * injector (primarily cwl, cwh, req_fuel and injpwm) * trigger config (you know that already, according to InputTrigger/AudiTrigger )
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.