#####  
 ##      
  ####   
   ####  
 #    #  
 #####   
         

  __  __ 
 |  \/  |
 | |\/| |
 | |  | |
 |_|  |_|
         

    #    
         
   ##    
    #    
    #    
    #    
   ###   
         

   ###   
  ## ##  
  ##     
 ####    
  ##     
  ##     
 ####    
         

_________
\__   __/
   ) (   
   | |   
   | |   
   | |   
   | |   
   )_(   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
My brothers BMW E34 M5 engine will be put in my E24 for install and tuning, and will be sold afterwards. Engine Specs: * engine block + head 3.6l 24v (S38b36) 6cyl inline * Intake/exhaust + wiring harness + ECU of the newer version 3.8l (S38b38) ** just curious, what connector ?'''its a 88pin connector''' Q: '''is there any source on a 88pin connector at the webshop or elsewhere?''' * not in webshop (2008-01) * elsewhere ? hmm.. not easy to get. Let us know if you can source (even if only in 200-500 quantity) * coil on plug, distributorless ignition of 3.8l ** power ignition outputs needed, because measured coil resistance is '''0.8 Ohm between Pin 1 and 15''' ** What do you measure with DVM probes touched ? I don't understand the question, what is DVM (digital volt meter?) dvm = digital volt meter, also called multimeter, the tool you used to meaure with, the question is, what does your meter read with probes in contact with each other /Emil 0.4 measured with probes in contact. We will use the original wireharness for most connections. Items to buy: The board has to be populated for '''primary and secondary triggers of VR-type'''. Looks OK you can go through [http://shop.vems.hu/catalog/product_info.php?cPath=1&products_id=48 assembled item in shop] a last time to think it over *Genboard v3.3 * [http://shop.vems.hu/catalog/product_info.php?cPath=1_9&products_id=52 shop/input drivers/additional VR interface] that is LM1815 for sectrig VR *8 ignition drivers *10 injector drivers (WBO2 and a normally unused spare) *Ignition driver insulator sheet *serial jack kit ** we usually apply RS232 through EC18/14-15 and DSUB9 in harness, but your choice'''that's for the keyboard-connection''' *Alubos EC frontplate *Alubos endplate ** dsub9 type (for LCD) recommended * 2xAlubos gaskets *Alubos 1600 ** 6 drill type. Do you want it with the 2 mounting screws ? (just write in the order note) * 3xclamping plate *Econoseal18 pcb *Econoseal36 pcb * maybe pneumatic connector VIV6464 type (for internal mounting of sensor) *Econoseal36 wire side *Econoseal18 wire side *250 kPa Map sensor ** some pneumatic tube, 180C 6/4mm *2 Premium axial NTC temp sensor *Wideband O2sensor *Wideband connector *LCD 4x20 blue
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.