##      
 ##      
 ##  ##  
 ## ##   
 ####    
 ## ##   
 ##  ##  
         

 _   _ 
( ) ( )
| | | |
| | | |
| (_) |
(_____)
       
       

         
  #####  
 ##  ##  
 ##      
 ##      
 ##   #  
  ####   
         

 _______ 
(  ___  )
| (   ) |
| |   | |
| |   | |
| |   | |
| (___) |
(_______)
         

         
         
 ##   ## 
 ## # ## 
 ####### 
  #####  
  ## ##  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
This tutorial is written to explain all the trigger setup variables for the '''1.1.x series of firmware'''. There are two general types of trigger schemes, those that rely on a missing teeth to identify the wheel position and those that do not. This document deals with the latter. The examples here are taken from a Mazda 1.8l 4 cylinder BP engine's trigger scheme. With the settings here it should be trivial to make changes and adapt the configuration to variants of this scheme. First the Mazda distributor contains a disc with slots as follows: http://www.vems.hu/files/Fero/Mazda_BP8_CAS.jpg This camwheel rotates counterclockwise and is triggered via hall type sensor. This means either rising or falling edge pulses are appropriate. Looking closely at this wheel the waveform of a running engine will look like this graphed according to degrees of rotation on the cam. Since the crank rotates at twice the speed this graph also represents two complete crank revolutions. http://www.vems.hu/files/hackish/mazdatrigger.gif Dissecting the data presented here a number of details can be determined. Note that unless otherwise noted all measurements are expressed in degrees of cam rotation. Here, the primary pulse occurs 4 times per engine period and the secondary trigger only once. * The rising edge of any primary trigger occurs 80 degrees before TDC on the next cylinder. * The falling edge of any primary trigger occurs 33 degrees before TDC on the next cylinder. * The rising edge of the secondary pulse occurs 18 degrees before TDC1 * The falling edge of the secondary pulse occurs 57 degrees after TDC1 and 43 degrees before TDC3. Since these measurements are in cam degrees they are 1/2 of the crank measurement. This engine will never require 66 crank degrees of advance so we can use the falling edge of the primary trigger. Since this signal will occur closer to the actual engine event it will be slightly more accurate when the RPM is not constant. First the trigger types must be configured: '''primary_trigger''' This configuration parameter contains a number of bit flags: || '''Bit Position''' || '''1''' || '''0''' || || 0 || Rising edge trigger || Falling edge trigger || || 1 || Simple repeating trigger type || Missing tooth trigger type || || 2 || Filtering enabled || Filtering disabled || || 3 || Advanced trigger code || Disabled || || 4 || One missing tooth (ie 60-1) || Two missing teeth (ie 60-2) || || 5 || Fiat Stilo and Subaru triggers || Disabled || || 6 || Nissan trigger || Disabled || Here we wish to trigger on the falling edge, it is a simple repeating trigger type with filtering enabled <code> primary_trigger=06 </code> '''secondary_trigger''' || '''Bit Position''' || '''1''' || '''0''' || || 0 || Rising edge trigger || Falling edge trigger || || 1 || Disable this trigger || Enable this trigger || || 3 || Single tooth type || Multitooth type || || 4 || Cam Sync || Alien Advance || || 5 || reserved for future crank trigger scheme || Disabled || || 6 || Fiat Stilo and Subaru triggers || Disabled || The secondary trigger also uses the falling edge and is flagged as the cam sync channel. <code> secondary_trigger=18 </code> '''tooth_wheel''' For 1.1.x series firmwares running in 'non-missing' mode this is the number of teeth from the primary trigger that is seen between each cam synk pulse. So for this application where we have four primary trigger slots on a wheel rotating at cam speed we get tooth_wheel=04. <code> tooth_wheel=04 </code> '''reset_engphase_after''' Since the crank rotates at twice the speed of the cam then this value is normally 2x the tooth_wheel value <code> reset_engphase_after=04 </code> '''trigger_tooth''' For 1.1.x series firmwares running in 'non-missing' mode this tell the firmware which tooth to trigg from in relation to the H[1]table. trigger_tooth must be < another_trigger_tooth. For this application this only leaves trigger_tooth=0 <code> trigger_tooth=0 </code> '''another_trigger_tooth''' For 1.1.x series firmwares running in 'non-missing' mode this tell the ECU how many steps to take at a time in the H[1]table. For this application we want to use every entry in the H[1]table and which give us another_trigger_tooth=1 <code> another_trigger_tooth=1 </code> '''cam_sync_r_edge_phase''' '''cam_sync_f_edge_phase''' These two do not appear to be implemented in the 1.1.x code when used in "non-missing" mode. I suspect they can be used to provide a faster sync of the trigger when the cam sync pulse arrives. Both are set to 0xFF '''crank_minper''' This is the minimum time between trigger pulses. For this application where we use 2 trigger pulses per crank revolution it's 1/(2*8000/60)=0.00375s=3750us ''Not sure about the scale though, cross referencing config.txt with megatune indicates 25.6us resolution.'' The docs say this is the minimum period for the crank trigger. It is in 16us intervals. It's a filter that limit the max trigger frequency. </code> '''tooth_wheel_twidth1''' '''tooth_wheel_twidth2''' With no missing teeth these two values are used together as a 16 bit value for the number of degrees between on the primary triggers. This value does not reflect the 74 crank degrees of width in our primary trigger but the 180 crank degrees between falling edges. The value is stored in 1/4 crank degrees. The resulting value is 0x02D0 <code> tooth_wheel_twidth1=0xD0 tooth_wheel_twidth2=0x02 </code> '''ign_tdcdelay''' This parameter is very important as it must be chosen such that there are enough crank degrees of rotation to allow our maximum desired amount of timing advance. I do not know if this factors in dwell time or not. mcel?'''Dwell is started elsewhere so not related to this.''' This stores the number of 1/2 crank degrees from the primary trigger pulse to TDC. Since we use the falling edge of the primary pulse it is 33 cam degrees and 66 crank degrees before TDC. The resulting hex value in 1/2 degree increments is 0x84 <code> ign_tdcdelay=84 </code> The resulting trigger config for this Mazda BP engine is as follows: <code> primary_trigger=06 crank_minper=30 tooth_wheel_twidth1=0xD0 tooth_wheel_twidth2=0x02 ign_tdcdelay=84 tooth_wheel=04 reset_engphase_after=04 trigger_tooth=00 another_trigger_tooth=01 cam_sync_r_edge_phase=FF cam_sync_f_edge_phase=FF </code> Someone will have to explain to me step by step how the h[1] table works so I can add that in here.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.