__     __
 \ \   / /
  \ \_/ / 
   \   /  
    | |   
    |_|   
          
          

 ___   
(  _`\ 
| ( (_)
| |___ 
| (_, )
(____/'
       
       

 __          __
 \ \        / /
  \ \  /\  / / 
   \ \/  \/ /  
    \  /\  /   
     \/  \/    
               
               

         
     ##  
     ##  
  #####  
 ##  ##  
 ##  ##  
  #####  
         

 _______ 
(  ___  )
| (   ) |
| |   | |
| |   | |
| |   | |
| (___) |
(_______)
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
The marine plug will be wired as follows: || '''Function''' || '''EconoSeal pin''' || '''Harness Colour''' || '''Chassis Plug''' || || Sensor power 5V || 36-28 (+5V to sensors) || Orange || 2 (orange) || || Sensor ground || 36-26 || Black || 1 (black) || || Power ground || 36-5 || brown (chassis) || || || Power ground || 36-21 || brown (chassis) || || || Power ground || 36-32 || Black (chassis) || || || Flyback || 36-23 || green || || || Inj common +12V || 36-25 || || 3 (red) || || injector 1 || 36-7 (Injector A) || Red || 4 (red) || || injector 2 || 36-19 (Injector B) || gray || 5 (gray) || || injector 3 || 36-8 (Injector C) || Purple || 6 (purple) || || injector 4 || 36-20 (Injector D) || yellow || 7 (yellow)|| || CLT || 36-14 (CLT Coolant Temp) || lt brown || 18 (lt brown)|| || IAT || 36-2 (Intake Air Temp) || Pink || 19 (pink) || || TPS || 36-1 (TPS signal) || Green || 20 (green) || || MAP || 36-6 || pink || 21 || || crank position sensor || 36-27 (Primary Trigger) || Blue || 22 (gray) || || cam position sensor || 36-13 (Secondary Trigger) || Purple || 23 (purple) || || knock signal || 18-3 || || 24 || || knock ground || || || 1 (black) || || iac || 36-34 Coil #2 || orange || 12 (red blue) || || Oil pressure || cluster light || || || || reverse lights || chassis electrical || || || || turbo bulb on dash || 36-24 (Coil #6) || || chassis || || CEL bulb on dash || 36-10 (Coil #7) || gray || chassis || || Coil common || || || 3 (red) || || coil1 || 36-35 (Coil #0) || white || 8 || || coil2 || 36-33 (Coil #1) || brown || 9 || || Cluster RPM Gauge || 36-12 (Coil #5) || gray || Chassis electrical || || baro || || || 17 || || boost solenoid || 36-36 (Coil #3)|| gray || 10 || || cooling fan || 36-11 (Coil #4)|| pink || 11 || || Fuel Pump Relay || 36-15 || light Green||Chassis electrical || || nernst_cell || 18-13 || blue || WBO2 connector || || heater - || 18-18 || white || WBO2 connector || || pump - || 18-7 || yellow || WBO2 connector || || pump + || 18-9 || green || WBO2 connector || DB15 LCD & extras config: I am using a DB15 plug to connect a Noritake CU20025ECPB-W1J and any extras to the vehicle wiring harness. || '''JP_LCD''' || '''DB_15''' || '''Signal''' || '''Cable Colour''' || '''LCD Pin''' || '''LCD Signal''' || || 2 || 1 || GND || Black || 1 || GND || || 10 || 2 || VCC || Red || 2 || VCC || || || || || || 3 || NC || || 1 || 3 || RS || Yellow || 4 || RS || || 7 || 4 || RW|| Orange || 5 || R/W || || 8 || 5 || Latch || Blue || 6 || E (RD) || || || || || || 7 || DB0 || || || || || || 8 || DB1 || || || || || || 9 || DB2 || || || || || || 10 || DB3 || || 6 || 6 || Databit4 || White || 11 || DB4 || || 5 || 7 || Databit5 || Green || 12 || DB5 || || 4 || 8 || Databit6 || Violet || 13 || DB6 || || 3 || 9 || Databit7 || Brown || 14 || DB7 || Keyboard connection || '''JP_PS1''' || '''DB_15''' || '''Signal''' || '''Cable Colour''' || '''PS/2 Pin''' || || 1 (top) || 10 || VCC || Yellow || 4 || || 2 || 11 || GND || Orange || 3 || || 3 || 12 || Data || Brown || 1 || || 4 (bottom) || 13 || Clock || Green || 5 || Distributor Wiring || '''Distributor Pin''' || '''Factory Colour''' || '''Signal''' || || 1 || Black / Lt Green || GND || || 2 || White / Red || +12V || || 3 || White / Brown Spots || Trigger 1 || || 4 || Yellow / Blue || Trigger 2 || Now triggering is a problem here. Fero figured out the location of the slots so I didn't have to. http://www.vems.hu/files/Fero/Mazda_BP8_CAS.jpg When fed with 12V the trigger2 outputs 5V or 0. Great for the hall trigger setup. Thanks again to Fero. When the crank trigger is hooked up to the board it measures about 3.8v and 150mv.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.