_   _ 
( ) ( )
| `\| |
| , ` |
| |`\ |
(_) (_)
       
       

 ______  
(  ___ \ 
| (   ) )
| (__/ / 
|  __ (  
| (  \ \ 
| )___) )
|/ \___/ 
         

         
     ##  
     ##  
  #####  
 ##  ##  
 ##  ##  
  #####  
         

      ## 
  #####  
 ##  ##  
 #####   
  ##     
  #####  
 ##  ##  
 #####   

         
         
 ##   ## 
 ## # ## 
 ####### 
 ####### 
  ## ##  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Measuring ignition advance''' With a tooth wheel as crankshaft trigger, the genboard can be used to reconstruct the ignition map of an existing distributor or OEM ECU. Since the angular speed and position of the crankshaft are known, it is straight forward to calculate advance. When the config is setup to use a tooth wheel as primary trigger, the advance is measured by letting the secondary trigger ''tap'' the ignition coil. If the firmware is compiled ''without'' MS_COMPATIBILITY defined in ''my_make'', the measured advance and dwell can be logged using a program such as MegaTunix. Finally the log needs to be filtered and an ignition map generated, 'bin/linreg.pl' is recommended for doing that automatically. Michael uses a 36-2 teeth trigger wheel with TDC at the missing tooth. The missing tooth is not in the recommend position (max advance + 1..40 degrees) thereby potentially introducing inaccuracies when engine speed varies. ''trigger_tooth'' in config is set to the value 10 (dec) which delays the trigger by 10*10 degrees (360 degrees / 36 teeth) and reduces the inaccuracy. http://www.vems.hu/files/MichaelKristensen/mik_trigger.png The '''question''' is '''when''' will the missing tooth be detected? This is important because: 180 degrees = 10*10 degrees - tdc_delay/2 - unknown_detect_missing_tooth_delay tdc_delay (in this case 70 degrees) can compensate for the unknown delay, but the measured ignition advance table will be offset by a constant. Since the LM1815 gives a rising edge pulse when the VR sensor is in the middle of the tooth, the delay will be 10 degrees after TDC as in the picture. A 20 minutes drive with logging of ignition advance at various rpm/map load points: x = rpm, y = map [kpa], z = advance [degrees] (for the interested: ADU9336 ignition control box used in ex. MG Maestro) http://www.vems.hu/files/MichaelKristensen/mik_advance1.png The corresponding histogram showing frequency of advance degrees*2 observations: http://www.vems.hu/files/MichaelKristensen/mik_advance_hist1.png logfile: http://caffrey.dk/dump/log_20040318.zip I extracted statistics from it: simple averaging near gridpoints and running linear regression near the lines between 2 gridpoints: see bin/linreg.pl for both (Marcell). The holes in the map are indeed strange, a possible explanation is the old ignition ECU having problems generating certain (30/40/50 degrees) advances. It's almost certain that the old slow ECU is processing the high priority tooth-detection interrupt in that holes, therefore it cannot emit spark. A couple of interesting figures from the log file: WOT @ 4000 rpm: 38 degrees part throttle (50 kpa / 3000 rpm): 55 degrees idle (30 kpa / 1000 rpm): 30 degrees '''Measuring dwell period''' Besides measuring when the ignition event happened, the duration of the event is also measured. This can be used to measure the coil charge time - the ''dwell period''. Of course the duration of any other signal can also be measured, ex. injector opening time of existing ecu. Michael's coil is specified to have a 0.71-0.81 ohm resistance at 20C degrees. Measured dwell is around 4.4 ms. [http://caffrey.dk/dump/dwell_log.tgz A log file] showing how the dwell period changes as a function of battery voltage. First column is battery voltage (I'm not sure about the voltage divider, max seen battery voltage should be around 13.5V), second column is dwell period in ms. '''Measuring without megatunix''' - Is there any possibility to measure ignition advance with a perl script or any other method? - If the trigger wheel is unknown, is it possible to reconstruct the teeth number and missing tooth position with the method above (measuring ignition signal from coil and measuring trigger signal as well in the same time)
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.