## ## ## # ## ####### ##### ## ##
_ _ ( ) ( ) | |_| | | _ | | | | | (_) (_)
### ## ## ## #### ## ## ####
## ## ## ## ## ## ##### ## ####
##### ## ## ## ## ##### ## ##
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: '''Mercedes AMG M113''', 5L V8 without compressor from factory (not M113K) but compressor DIY-added with lot of mech-work. Same set of sensors as the V6 M112 engine (just in case it is easier to find docs for that). '''V8 engine 15426378 firing order''' (CL500 or similar chassis) [https://en.wikipedia.org/wiki/Mercedes-Benz_M113_engine M113 engine] 3 valves and dual sparkplugs per cyl (16 sparkplugs total), no VVTI '''Engine started immediately after sorting out the mess of ignition transformer connections:''' * they were different on paper documentation and real life, no surprise it did not want to start ** on top of that, EC36/31 low current p259 output was connected instead of EC36/33 IGBT to drive 2 igncoils, luckily it did not blow up (nothing was configured on that p259 output). ---- '''Ign outputs ... ''' - will be overloaded this way '''However, because 1-6 and 6-1 are driven in pairs, 4 igncoils from 2 outputs with opponent cyl hard-wired''' * currently 16 ignition transformers can only be driven per crankrot (ign-dualout), equivalent to 32 passive igncoils driven from the 8 IGBTs inside VEMS ** on top of that, VEMS ECU is installed in the engine bay. ** This is outside the safe envelope, it is impossible to guarantee proper cooling and operation while driving 16 ignition transformers at double frequency (equivalent to 32) from the engine bay... '''15426378''' recommended output connection: * cyl1 EC36/35 ignch0 * cyl6 EC36/33 ignch1 * cyl5 EC36/34 ignch2 * cyl3 EC36/36 ignch3 * cyl4 EC36/11 ignch4 * cyl7 EC36/12 ignch5 * cyl2 EC36/24 ignch6 * cyl8 EC36/10 ignch7 ---- '''Had to do some investigation (or hint, eg pinout) regarding M113 sectrig HALL sensor''' * engine harness schematic might also cast some light on this? ** although both GND and output seems to be connected to ECU (camHALL GND not connected to other GND-s in the harness, only inside the ECU) ---- '''Primary trigger VR (1072 Ohm)''' * Factory trigger seems to be "inverted", ** swapped wires so that falling edges are correct at missing tooth ** verified (slowly rising in tooth-gap) ** [https://mbworld.org/forums/mercedes-tech-talk/646349-mercedes-v8-m113-cam-crank-scope-example-log.html scopeshot here] is good (wire swapping not needed if the same signal), may or may not be applicable... * Factory ECU pin37, (pin38) are the crankshaft VR input '''Primary trigger VR signal is really trash''' * some teeth amplitude are 1.6 times greater. ** interestingly, not even the tooth right after missing tooth, but 4th tooth was bigger... Greater in positive direction, even greater going negative. ** most likely interference from ignition (?) ** need to try with ignition disabled, but battery was almost drained, had to stop. ** Most likely '''Shielded cable is needed. Shield connected at ECU side only''', and GND and VR-signal wires inside connected on both sides. ** VR modification: either primtrig LM1815 pin5=5V to disable adaptive threshold, or R181=270k or similar ** signal amplitude is otherwise OK, but high voltage noise is unknown. ** Perhaps a 1k pulldown could be useful at the same time if signal amplitude allows... ---- '''Secondary trigger: 1 pulse per camrot''' '''Bosch 0.232.103.027''' - '''sensor had contact problem at male receptacles (oxide? even with new heatshrinked receptacle it did not work first''' * Verified HALL sensor for sure (with +12V supply, 30..40mA supply current) ** Pulls to GND (with pullup resistor in ECU) '''pinout (Verified: pin1,2,3 are: GND, HALL output pink, +12V red-blue)''' * '''pin1: GND''' from Bosch ECU/pin39 (low current connector) '''brown-green''' * '''pin2: output''' pink = Bosch ECU/pin 40 (low current connector) * '''pin3: +12V''' (in factory harness same net as injector shared +12V) '''red-blue''' Similar bosch camshaft Hall sensor's datasheet: [https://www.datasheets.com/en/part-details/0-232-103-037-bosch-407068925#datasheet 0232.103.037] - All "0 232 103 XXX" sensors seem to bee camshaft sensors. '''Big mistery with secondary trigger''', * '''Ours did not react to hammer moved near and away (when powered +12V, of course)''' * Apparently same sensor as in [https://www.youtube.com/watch?v=wUMNT3ncpNg this m112 video] (and even same pins 39,40 in the factory engine harness, although the factory harness is not actually used), but our sensor does NOT react. ** '''IN THE VIDEO, middle pin seems to be signal output as assumed''' (he attached probes reversed in DVM, never mind)... 12V when no iron, and 0V when ferromagnetic tool is close ---- '''DBW''' * currently factory ECU drives it, but VEMS is prepared (with bridgeoutput driver) ---- '''Ignition''' * 16 sparkplugs (dual sparkplugs per cyl) * only 8 passive ignition transformers ---- '''URLS''' * MembersPage/PeepPaadam/MercedesAMGSL - very similar * MembersPage/MercedesSelFivePointSix * MembersPage/AmgSlovakia much more sophisticated Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.