##    
         
  ###    
   ##    
   ##    
  ####   
         

   ____  
  / __ \ 
 | |  | |
 | |  | |
 | |__| |
  \___\_\
         
         

 #       
 #       
 #   #   
 #  #    
 # #     
 ## #    
 #   #   
         

    ##   
         
   ###   
    ##   
    ##   
    ##   
 ## ##   
  ###    

         
         
  #####  
 ##      
  ####   
     ##  
 #####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
I have a Volvo B230 4 cyl 8 valve engine with simple trigger: * Two teeth on crank at about 80 degrees before TDC * Camsync occuring at TDC. '''Before the fuelpump turns off''' (pump_on_mintime, recommended setting is 3..4 sec) '''sync is quick and engine starts fast''' * '''After the fuelpump turns off, Coiltype + camsync syncup is very slow''' (then suddenly the "Cranking On" flag turns on and it starts and runs fine) ** after some investigation it was found that engine.status_trig=0 was added from 1.2.7 in favor of Maserati caused this slowsync after fuelpump_min_time has passed after powerup. ** fixed in [https://svn.x-dsl.hu/f/ 1.2.15] (since 2013-08-20). Configure longer "fuelpump ON after powerup" time if need to use 1.2.7 .. 1.2.14 fw for some reason ** Note: also working on missing tooth with camsync (overcautios syncup conditions cause slower than 1.1.96) ---- Here is a firmware 1.2.11 vemslog of starting and running the engine. Notice the initial cranking with no rpm signal, then suddenly "cranking on" and it starts. * http://www.vems.hu/files/MembersPage/MattiasSandgren/C004andCamSync/1.2.11-hard-to-sync.vemslog If I run firmware pre 1.2.x it will sync and start immediately. * What can I do about improving this for 1.2.0+ firmware? ** we'll investigate in detail after vemscfg or vemslog is provided. It would be very nice to also have "pre-1.2.x" vemscfg for reference, if possible. * Are there any settings I have missed? ** unlikely, although the reftooth order might effect speed of starting (reftooth=0 entry in position 0 is theoretically best) I have tried this on a V8 with only 90 degrees between crank teeth, it was almost impossible to get it starting. Downgrade to 1.1.96 and it fires right up every time. Here is a typical cranking sequence, and clear to see seven (7) crank rotations before it syncs - with no fuel, so it didn't start, only for triggerlog cranking. http://www.vems.hu/files/MembersPage/MattiasSandgren/C004andCamSync/1.2.11-c004-camsync-hard-to-sync.triggerlog http://www.vems.hu/files/MembersPage/MattiasSandgren/C004andCamSync/1.2.11-hard-to-sync.png Here are my basic settings, anything to be changed here? http://www.vems.hu/files/MembersPage/MattiasSandgren/C004andCamSync/1.2.11-hard-to-sync-settings.png
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.