##  # ## 
##  #  # 
 ## ## # 
 ### ##  
  ## ##  
  #   #  
         

 ###     
  ##     
  ##     
  #####  
  ##  ## 
  ##  ## 
 ###  ## 
         

 _______ 
(  ____ )
| (    )|
| (____)|
|  _____)
| (      
| )      
|/       
         

 ###     
  ##     
  ##     
  #####  
  ##  ## 
  ##  ## 
 ######  
         

   ___  
  / _ \ 
 | | | |
 | |_| |
  \__\_\
        

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Engine setup''' * V12 60 degree even-fire * maximum RPM is: ..... (interesting for ignition hardware peak current) * Mounted in a boat (pro-longed high load compared to a car) * Two spark plugs per cylinder, total 24 spark plugs (12 wasted spark coils) ** Bosch Motorsport 3x2 coilpacks (4 pcs required for one engine) ** could be driven from 6 IGBT-s (IGBT can handle the double current if dwell is set sufficiently - not too high, and peak RPM < 7000 RPM) ** Beru 3-channel ignition modules (min 10 mA drive current) * One fuel injector per cylinder ** Siemens High-Z 9 Ohm fuel injectors * 24-1 crank mounted trigger wheel (or 24-2 is also OK) Due to lack of outputs I will handle the engine electrically as an inline 6 cyl. '''Two injectors per injector output.''' * Can one FET handle sustained high duty cycle with sufficient cooling? ** yes, 100% duty upto about 5 (or even 6A) is OK. (the FET's peak current is about 14A but we specify much lower) * Two injectors 9 Ohm results in 4.5 Ohm @ 14 Volts = 3 Amps ** yes, 3A is no problem at all. Make sure to connect flyback wire, of course. '''Driving the ignition modules''' * Six outputs required - using four stepper outputs and two logic level outputs * Drive current requirement per ignition module input is minimum 10 mA ** Driving two channels is a minumum 10x2 = 20 mA up to 40 mA. ** Can the IGBT logic driver handle this? 20mA : yes, 40mA: no (but 40mA should not be needed anyway) ** Suitable resistor values on board?. 255 Ohm is suitable to drive one module, but 120-130 Ohm needed to drive 2 modules (that still protects the i259 chip's outputs). ** I would recommend 6 IGBTs and 2 logiclevel outputs with appr 120 Ohm (=510x150-160 Ohm or so) current-limiting than it can be decided later to use logiclevel or power-outputs. It is also posssible to use 4 stepper (with module driving 8 transformers) and 4 IGBT outputs driving 4 transformers (configured in igndualout, that is perfectly valid and correct for a multispark engine like this !), either 4 driving the 4 modules individually (best setup) or possibly 2*2 connected in parallel (yes, connecting low-side switches in parallel is also safe). * Stepper outputs are powerful, but current limiting resistors (100-200 Ohm) are recommended to protect from short circuits
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.