## ## ## # ## ####### ####### ## ##
_____ | _ | | | | | | | | | \ \_/ / \___/
# ### ## # ## # # ### # #
______ | ___ \ | |_/ / | ___ \ | |_/ / \____/
_______ ( ____ \ | ( \/ | (__ | __) | ( | ) |/
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: '''BMW E30 323 with M20B25 Turbo''' http://savarturbo.se/stuff/images/peppe_e30_tic/peppe_e30_turbo.jpg ---- '''The engine''' * Inline 6 cylinder BMW M20B25, 2.5 litres, ignition order 153624. * Wastefire ignition with Ford EDIS wasted spark coils (stock 60-2 trigger wheel) * Sequential fuel injection with no cam sensor and low-Z 720 cc/min injectors * Custom engine harness '''The turbo system''' * PPF turbo manifold (pulse-split) * External wastegate 50 mm from Boström Turbo Teknik * 3.5" downpipe and exhaust system out through the (no muffler) * Dump valve by Simon Marmander * Custom large intercooler * Holset HX50 turbo The config and tables will be updated on this page, and documented properly given some free time. Here they are: [http://www.vems.hu/files/MembersPage/MattiasSandgren/PeppeBmw/config.txt config.txt] and [http://www.vems.hu/files/MembersPage/MattiasSandgren/PeppeBmw/tables.txt tables.txt] Bear in mind that fuel has not been set properly, including afterstart and other enrichments. ---- '''Progress''' Above 6000 rpm this engine has run into the problem with the ignition dwell. The Ford EDIS coils need 4 ms dwell but that is simply not possible since the current method used in firmware doesn't allow overlapping dwell. At 7000 rpm one revolution of the engine takes 8.57 ms and there are three ignition events. The time between each ignition event is 2.86 ms on a 6 cyl engine, and there is currently 400 us "coil off time" which means an effective 2.46 ms dwell on coils that need 4 ms. There is little point in having 8 ignition drivers with this limitation. We hope this will be resolved by spring 2006 when the car will be on the road again for some serious tuning to get the most power out of the engine. The engine is running well but we have established that the poor fuseholder that was initially used caused 2 injector drivers to break, they can open if I work them manually (mdh..) (even with appr. 1A load ?) but give no measureable amount of fuel through the injector if used. This doesn't explain why the IGBTs show inproper diode voltage, they have internal clamping for the back EMF and of the two IGBTs that measure diode voltage - only 00 was used to drive a coil, 06 was never used. The injector FETs that died probably didn't have flyback of the proper voltage at the instant that the injectors they fired were closing, they had to take the back EMF. The 2 FETs and 2 IGBTs are replaced later this winter. The main problem we have now is tuning the fuel injector characteristics, these are big 720 cc/min injectors and are very fast. How fast is yet to be determined. As the idle only requires about 0.6-0.7 msec opening time it's critical to get this right. I guess experimentation is the only way to figure this one out. * I'm starting out with about 100 usec opening time and 150 usec rampup, but it doesn't work too well. These are the settings that Emil used on a 4 cyl Volvo with 1000 cc injectos, same brand of injectors. ** 100 usec opening time is against recommendations. use injopen=0 and very low battfac (100usec or so). injocfuel=900usec (rampup time) can be good for fast injectors, but this really requires some experimentation (usually above 1000usec gives best result). Similar injectors have been used on a car that Emil tuned, but the numbers don't seem to match on this engine. Two of the injector FETs are unusable, they will switch to ground if I activate them manually with mdhx0 commands but on a running engine there is hardly any fuel coming out of the injectors. These two were probably damaged by a bad connection in a cheap fuse holder that we used earlier and my fear is that the remaining FETs have been affected as well even though we seem to have no problem with the engine at higher load. But we have had problems tuning the idle and low load. Would a symptom be that they have problems with short injector opening times? As the manual activation seemed to work, perhaps the short opening times used in a running engine are less precise if they are damaged. But I will try your recommandations and run injopen=0 and increase rampup to begin with. ---- '''Some pictures of the car and engine''' [http://savarturbo.se/stuff/images/peppe_e30_tic/185.jpg http://savarturbo.se/stuff/images/peppe_e30_tic/tn/185.jpg] [http://savarturbo.se/stuff/images/peppe_e30_tic/186.jpg http://savarturbo.se/stuff/images/peppe_e30_tic/tn/186.jpg] [http://savarturbo.se/stuff/images/peppe_e30_tic/187.jpg http://savarturbo.se/stuff/images/peppe_e30_tic/tn/187.jpg] [http://savarturbo.se/stuff/images/peppe_e30_tic/188.jpg http://savarturbo.se/stuff/images/peppe_e30_tic/tn/188.jpg] [http://savarturbo.se/stuff/images/peppe_e30_tic/189.jpg http://savarturbo.se/stuff/images/peppe_e30_tic/tn/189.jpg] [http://savarturbo.se/stuff/images/peppe_e30_tic/harness_build_1.jpg http://savarturbo.se/stuff/images/peppe_e30_tic/tn/harness_build_1.jpg] [http://savarturbo.se/stuff/images/peppe_e30_tic/motor_testad.jpg http://savarturbo.se/stuff/images/peppe_e30_tic/tn/motor_testad.jpg] ---- '''History''' I'm helping a local guy with installing a Genboard on a M20B25 BMW '''inline 6 cyl''' engine with Bosch L-jetronic electronics and intake and distributor ignition. The M20B25 originally doesn't come in this configuration (Motronic only) but a previous owner swapped out the block and head of the 323 for 2.5 litre parts and retained the electronics and intake (very stupid, engine ran lean on too small injectors). The stock harness will be cut-up and partly re-used and directly wired to EC connectors - a lesson learned from a previous BMW 728 project with similar electronics, meaning the stock L-jetronic connector and box will not be used. ---- *WikiAdvert: mailto:mattias.sandgren@savarturbo.se Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.