_______ ( ___ ) | ( ) | | | | | | | | | | | /\| | | (_\ \ | (____\/_)
#### ## ## ## ## ## ## ####
_ _ | | | | | |__| | | __ | | | | | |_| |_|
______ | _ \ | | | | | | | | | |/ / |___/
#### ## ## ## ## ## ## ## ## ####
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: '''BMW E30 323 with M20B25''' ---- '''The engine''' * Inline 6 cylinder BMW M20B25, 2.5 litres, ignition order 153624. * Wastefire ignition with Ford EDIS wasted spark coils (stock 60-2 trigger wheel) * Sequential fuel injection with no cam sensor and low-Z 720 cc/min injectors * Custom engine harness '''The turbo system''' * PPF turbo manifold (pulse-split) * External wastegate 50 mm from Boström Turbo Teknik * 3.5" downpipe and exhaust system out through the (no muffler) * Dump valve by Simon Marmander * Custom large intercooler * Holset HX50 turbo The config and tables will be updated on this page, and documented properly given some free time. Here they are: [http://www.vems.hu/files/MembersPage/MattiasSandgren/PeppeBmw/config.txt config.txt] and [http://www.vems.hu/files/MembersPage/MattiasSandgren/PeppeBmw/tables.txt tables.txt] Bear in mind that fuel has not been set properly, including afterstart and other enrichments. ---- '''Questions''' When I measure the diode voltage through the IGBTs output to ground I get 740 mV on output 00 and 06. I get nothing when I measure the others. On other boards I can't measure any diode voltage on any output, so if the norm is that no diode voltage can be measured - then something is not normal here. The heatsink part of the IGBTs may have touched one another, effectively shorting the outputs. It seems to have been run this way and due to the soldering on the board (not by me by the way) and it is _very_ difficult to get them pointing straight. ---- '''Some pictures of the car and engine''' [http://savarturbo.se/stuff/images/peppe_e30_tic/185.jpg http://savarturbo.se/stuff/images/peppe_e30_tic/tn/185.jpg] [http://savarturbo.se/stuff/images/peppe_e30_tic/186.jpg http://savarturbo.se/stuff/images/peppe_e30_tic/tn/186.jpg] [http://savarturbo.se/stuff/images/peppe_e30_tic/187.jpg http://savarturbo.se/stuff/images/peppe_e30_tic/tn/187.jpg] [http://savarturbo.se/stuff/images/peppe_e30_tic/188.jpg http://savarturbo.se/stuff/images/peppe_e30_tic/tn/188.jpg] [http://savarturbo.se/stuff/images/peppe_e30_tic/189.jpg http://savarturbo.se/stuff/images/peppe_e30_tic/tn/189.jpg] [http://savarturbo.se/stuff/images/peppe_e30_tic/harness_build_1.jpg http://savarturbo.se/stuff/images/peppe_e30_tic/tn/harness_build_1.jpg] ---- '''History''' I'm helping a local guy with installing a Genboard on a M20B25 BMW '''inline 6 cyl''' engine with Bosch L-jetronic electronics and intake and distributor ignition. The M20B25 originally doesn't come in this configuration (Motronic only) but a previous owner swapped out the block and head of the 323 for 2.5 litre parts and retained the electronics and intake (very stupid, engine ran lean on too small injectors). The stock harness will be cut-up and partly re-used and directly wired to EC connectors - a lesson learned from a previous BMW 728 project with similar electronics, meaning the stock L-jetronic connector and box will not be used. ---- *WikiAdvert: mailto:mattias.sandgren@savarturbo.se Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.