___   
(  _`\ 
| (_(_)
|  _)_ 
| (_( )
(____/'
       
       

         
         
  ####   
 #    #  
 ######  
 #       
  ####   
         

   ##    
   ##    
  #####  
   ##    
   ##    
   ## ## 
    ###  
         

         
  ####   
 ##  ##  
 ######  
 ##      
 ##      
  ####   
         

         
         
 #    #  
 #    #  
 #    #  
 #   ##  
  ### #  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''AVR boot code how to''' Due to a failure with the electrical system in the car last year, we had to replace the AVR, the new chip was missing a boot loader so this page is about what I did to program the AVR. ( Guidelines copied from MembersPage/SteinOvePrestmo/MyNotes ) ---- The tool used was '''avrdude''' which can be found here: http://www.bsdhome.com/avrdude/ Contents of avrdude.conf file: <code> programmer id = "bsd"; desc = "Brian Dean's Programmer, http://www.bsdhome.com/avrdude/"; type = par; vcc = 2, 3, 4, 5; reset = 7; sck = 8; mosi = 9; miso = 10; ; </code> The boot loader hex file was swiped from an old firmware that was compilable (no WBO2 code removed, etc). <code> D:\VEMS>avrdude -c bsd -p m128 -U flash:w:main.hex avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.00s avrdude: Device signature = 0x1e9702 avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed To disable this feature, specify the -D option. avrdude: erasing chip avrdude: reading input file "main.hex" avrdude: input file main.hex auto detected as Intel Hex avrdude: writing flash (131072 bytes): Writing | ################################################## | 100% 50.61s avrdude: 131072 bytes of flash written avrdude: verifying flash memory against main.hex: avrdude: load data flash data from input file main.hex: avrdude: input file main.hex auto detected as Intel Hex avrdude: input file main.hex contains 131072 bytes avrdude: reading on-chip flash data: Reading | ################################################## | 100% 48.36s avrdude: verifying ... avrdude: 131072 bytes of flash verified avrdude: safemode: Fuses OK avrdude done. Thank you. </code> ---- This cable is to be used togheter with the "-C bsd" command in AVRDUDE ||AVR pin command||ISP header #||Parallel port pin||Notes|| ||AVR /RESET||5||7||Yellow|| ||AVR SCK (clock input)||3||8||Black|| ||AVR PDI (RXD) (instruction in)||4||9||Red|| ||AVR PDO (TXD) (data out)||1||10||Orange|| ||Signal Ground||6||18||Brown|| * MOSI and MISO are not used. Correct pins from the schematics AVR pin 2 = RXD/PDI -> ISP header Pin4, AVR Pin3 = TXD/PDO -> ISP header pin 1 This is what it looked like: http://www.vems.hu/files/MembersPage/MattiasSandgren/avr_isp_cable/avr_isp_cable_attached.jpg http://www.vems.hu/files/MembersPage/MattiasSandgren/avr_isp_cable/avr_isp_cable_ends.jpg
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.