_     
| |    
| |    
| |    
| |____
\_____/
       
       

         
         
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
    ##   
 ####    

  ______ 
 |  ____|
 | |__   
 |  __|  
 | |____ 
 |______|
         
         

         
 ##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
         

 _____ 
(_   _)
  | |  
  | |  
  | |  
  (_)  
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Matti Juntunens Nissan 200SX S13 "Diesel-Doris" ''' http://www.vems.hu/files/MembersPage/MattiasSandgren/MattisNissan/mattis_nissan200sx_s13.jpg '''Questions''' I'm preparing for assisting a startup attempt: What is the preferred firmware for the VehicleFitment/Nissan 24-1 trigger ? 1.1.18 was tested, doesn't 1.0.73 work? And if 1.1.18 is the one to go with, what vemsv3.ini should one use, does the one that comes with the 1.0.73 MegaTune package work ? MembersPage/PhatBob 1.1.18 is the one to use, this release should be good for you: http://vems.hu/www.vems.co.uk/VEMSInstalls/VemsMT1.1.18Nissan.zip '''VEMS Genboard specification''' 1-wire interface: No \\ ignition driver: 4+4 as described on VehicleFitment/NissanCOPs \\ Knock and EGT: Knock and 2 EGT \\ LCD and PS2: Yes \\ MAP connection: 400 kPa on-board (5/3 mm pneumatic) \\ mounting-style: no screws \\ PowerFlyback: No \\ primary_trigger: Hall \\ secondary_trigger: Hall '''Engine specification''' * Nissan CA18DET, 1.8 litre 4 cyl * Custom exhaust manifold * Custom intake manifold * H-beam rods and Wiseco pistons * Upgraded oil cooling system * Turbo is Holset HX35, 54/60 in/out * 440 cc low-Z injectors * Stock COP ignition system * '''Uses 24-1 trigger wheel as described here''' : VehicleFitment/Nissan ---- MembersPage/PhatBob We have our first CA18DET running on the 24+1 trigger disk, with very goode results: http://i5.photobucket.com/albums/y152/APT/DYNOSM1.gif Power would have been higher and smoother if the 7psi actuator on the turbo (GT2871) had been stronger. We hope to get better pressure control with a 15psi actuator. http://i5.photobucket.com/albums/y152/APT/DYNOSM2.gif The owner reported back from his first track test that the engine was strong and responsive throughout the rev range. We have used the standard wiring loom, COPs etc via the use of a harness adaptor: http://media.sxoc.com/contributors/sm/S13b/S13HarnessAdaptor.jpg
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.