_   _ 
( ) ( )
| `\| |
| , ` |
| |`\ |
(_) (_)
       
       

 _       
( (    /|
|  \  ( |
|   \ | |
| (\ \) |
| | \   |
| )  \  |
|/    )_)
         

         
  ####   
     ##  
  #####  
 ##  ##  
 ##  ##  
  ### ## 
         

    #    
 ######  
   ##    
   ##    
   ##    
   ## #  
    ##   
         

   ____ 
  / ___|
 | |  _ 
 | |_| |
  \____|
        

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
''''Eric Wiklunds Volvo 142 Turbo'''' This car shares a lot with Jonas car: MembersPage/MattiasSandgren/VolvoBtwenty Basically the same engine configuration, only this one is turbo-charged. * Stock B20 block * 8-bolt crank * forged KS pistons * F cam (300 degree duration, 111 degree lobe separation, 11 mm valve lift) * head ported by Jens Gustavsson * 3K K27 turbo (51 in/65 out) * home made turbo adapter to stock N/A manifold * home made wastegate * home made intercooler (from a large diesel truck) * MSD/Holley fuel injectors 895 cc/min @ 3 bar ---- '''News''' '''2007-07-31''' None of the MCP3208 analog inputs work, this explains the problems with the EGT inputs. The chip seems to have +5V and ground, but MegaTune reports randomly flickering values between 0 and 5.0 Volts in the datalogs. The chip has probably been damaged about two years ago when we first installed everything, the harness was then redone because it was only used to control ignition and datalogging. I don't think there is reason to suspect anything wrong in the harness at this point. It is very likely the problem is with the MCP3208 chip? * the mcp3208 is very easy to damage, eg by applying higher than 5V to the input (+14V or static electricity) ** the AVR is unlikely to be damaged (though the only chip that talks over SPI is the MCP3208) It sounds sane to replace mcp3208 and try again on the desk. You can also install internal pullups (2k7 recommended) if you don't have already '''2006-10-23''' The engine now has a rebuilt bottom-end and there must have been an incredible amount of blow-by on the old bottom-end because VE increased almost 20% at higher loads, with no other changes. The turbo is much more responsive too. The injectors have been wired in series with a 6.8 Ohm 50W resistor for each injector and a transient protection diode (Zener) has been added to the flyback wire. The total opening time has increased for a given effective pulse width but the accuracy seems to have increased due to more effective flyback control. There is still problems with EGT readings, I will look into that very soon as the car will go on to a dyno in a few weeks and then put into storage for the winter. '''2006-06-11''' The car ran 12.34 sec @ 174 km/h at the "local" dragstrip in Piteå, north of Sweden. A very nice result for such a simple setup. 110 kPa boost and very little tuning. [http://www.fickpingis.com/wiklund.wmv Movie here] http://race.ulkhyvlers.net/dragrace/Pite/060611/DSC03153.JPG ---- '''Genboard specific configuration''' This is a v3.2 with production number 126. Both triggers are configured for Hall. MCP3208 channels 5,6 and 7 are wired to EC18 pins 6, 12 and 16. EGT - only EGT #2 is wired in (MCP3208-4 ?), see page about EGT trouble: MembersPage/MattiasSandgren/EricsVolvoTurbo/EGT Using power flyback for the injectors with a 30V transient suppression diode.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.